EG60 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE (for TMC Made): ADJUSTMENT; 2019 MY Corolla Corolla Hatchback [06/2018

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001CZK4
Model Year Start: 2019	Model: Corolla Hatchback	Prod Date Range: [06/2018 - 01/2019]
Title: EG60 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE (for TMC Made): ADJUSTMENT; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]

ADJUSTMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly adjustment are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane Control System
		Pre-collision System
		Lighting System (w/ AFS)(EXT)
	Initialize back door lock	Power Door Lock Control System
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
	ECU communication ID registration (Immobiliser system)	Engine start function
	Code registration (Smart Key System (for Start Function))	Wireless Door Lock Control System Smart Key System (for Entry Function) Smart Key System (for Start Function) Steering lock function

NOTICE:

After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. SECURE VEHICLE

(a) Fully apply the parking brake and chock a wheel.

CAUTION:

Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here

4. REMOVE BATTERY

Click here

5. REMOVE CONSOLE BOX ASSEMBLY

Click here

6. REMOVE RADIATOR SUPPORT OPENING COVER

Click here

7. REMOVE INLET NO. 1 AIR CLEANER

Click here

8. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here

9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Click here

11. REMOVE ECM

Click here

12. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

13. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:

After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.
If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.

(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.

(b) Slide the slider of the transmission control select cable in the direction indicated by the arrow in the illustration and pull the lock piece outward.

*a	Slider
*b	Lock Piece
*c	Slide
*d	Pull

NOTICE:

Check that the lock piece is pulled out.
Push the end of the transmission control select cable all the way to the base of the floor shift shift lever assembly pin.
Connect the transmission control select cable so that the lock piece faces the driver side.

*a	Lock Piece

(d) Align the hole of the outer select lever with the hole in the manual transmission case.

*1	Outer Select Lever
*a	Hole of Manual Transmission Case
*b	Hole of Outer Select Lever

(e) Insert a bolt into the aligned holes to secure the outer select lever in place.

NOTICE:

Do not push in the bolt forcefully or damage the front transaxle case.

HINT:

Use a bolt with a diameter of 6 mm (0.236 in.) and a length of at least 36 mm (1.42 in.).
Depending on the bolt diameter, it may be difficult to insert the bolt. In that case, use a bolt with a diameter smaller than 6 mm (0.236 in.).

(f) Push the slider shaft against the cam wall.

NOTICE:

Do not pull up the slider shaft.
When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

*a	Slider Shaft
*b	Cam Wall

(g) Push the lock piece into the adjuster case.

*a	Lock Piece	*b	Adjuster Case
*c	Push	-	-

NOTICE:

Securely push in the lock piece until the slider lock is engaged.

(h) Remove the bolt to release the select outer lever.

14. INSTALL BATTERY CLAMP SUB-ASSEMBLY

Click here

15. INSTALL ECM

Click here

16. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here

17. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here

18. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Click here

19. INSTALL INLET NO. 1 AIR CLEANER

Click here

20. INSTALL RADIATOR SUPPORT OPENING COVER

Click here

21. INSTALL CONSOLE BOX ASSEMBLY

Click here

22. INSTALL BATTERY

Click here

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click here