Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CYQ7 |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: SEAT: FRONT SEAT CUSHION HEATER (for Manual Seat): REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat cushion heater assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
-
Occupant detection ECU
-
Front passenger seat
|
Zero point calibration (Occupant Classification System)
|
-
Occupant Classification System
-
Passenger airbag ON/OFF indicator
-
Airbag System (Front passenger side)
-
Seat Belt Warning System (Front passenger)
|
|
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
-
If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. REMOVE FRONT SEAT ASSEMBLY
Click here
3. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER
Click here
4. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)
Click here
5. REMOVE RECLINING HINGE COVER
Click here
6. REMOVE RECLINING ADJUSTER RELEASE HANDLE
Click here
7. REMOVE LH SEAT SEAT ADJUSTER COVER CAP (for Driver Side)
Click here
8. REMOVE FRONT SEAT CUSHION SHIELD (for Driver Side)
Click here
9. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
Click here
10. REMOVE FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
Click here
11. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
Click here
12. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Click here
14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Click here
15. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY
(a) for Sporty Seat Type:
(1) Remove the 12 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. (for Cushion Heater Type A)
|
|
(2) Remove the 19 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. (for Cushion Heater Type B)
|
|
(3) Remove the 25 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. (for Cushion Heater Type C)
|
|
(b) for Sports Seat Type:
(1) Remove the 14 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. (for Cushion Heater Type A)
|
|
(2) Remove the 18 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. (for Cushion Heater Type B)
|
|
|