| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CYPV |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: SEAT: LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Manual Seat): REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during lumbar support adjuster assembly LH removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System |
|
|
Pre-collision System |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock |
Power Door Lock Control System |
|
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
- If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. REMOVE FRONT SEAT ASSEMBLY LH
Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REMOVAL](/t3Portal/stylegraphics/info.gif)
3. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER
Click here
4. REMOVE VERTICAL ADJUSTING HANDLE LH
Click here
5. REMOVE RECLINING HINGE COVER LH
Click here
6. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH
Click here
7. REMOVE LH SEAT SEAT ADJUSTER COVER CAP
Click here
8. REMOVE FRONT SEAT CUSHION SHIELD LH
Click here
9. REMOVE FRONT SEAT INNER CUSHION SHIELD LH
Click here
10. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
11. REMOVE FRONT SEAT HEADREST SUPPORT
Click here
12. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Click here
13. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
|
(a) Disengage the clamp. |
|
(b) Disconnect the connector.
|
(c) Disengage the 2 claws to remove the 2 front seatback edge protectors from the front seatback frame sub-assembly LH. |
|
(d) Remove the lumbar support adjuster assembly LH from the front seatback frame sub-assembly LH as shown in the illustration.
|
Remove in this Direction |
14. REMOVE FRONT SEATBACK FELT LH
Click here
15. REMOVE FRONT SEATBACK EDGE PROTECTOR
Click here
|
|