INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

Make sure to hold the front wiper arm while lifting it, as lifting the front wiper arm by the front wiper blade may damage or deform the front wiper blade.

PROCEDURE

1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

(a) Push the windshield wiper motor assembly in the direction indicated by the arrow (1), then move the windshield wiper motor assembly in the direction indicated by the arrow (2) shown in the illustration to temporarily install it to the wiper link assembly.

	Install in this Direction (1)
	Install in this Direction (2)

(b) Install the windshield wiper motor assembly with the 3 bolts.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

(c) Apply MP grease to the pivot of the windshield wiper motor assembly.

*a Pivot of Windshield Wiper Motor Assembly

(d) Connect the No. 1 windshield wiper link rod to the pivot of the windshield wiper motor assembly.

*1 No. 1 Windshield Wiper Link Rod *a Pivot of Windshield Wiper Motor Assembly

(e) Connect the connector.

(f) Engage the 2 claws to install the sub wire harness.

2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

(a) Install the windshield wiper motor and link assembly as shown in the illustration.

Install in this Direction (1)

Install in this Direction (2)

(b) Engage the motor grommet as shown in the illustration.

*a	Motor Grommet
	Install in this Direction

NOTICE:

Be careful not to damage the windshield glass when installing the windshield wiper motor and link assembly.

(c) Install the windshield wiper motor and link assembly with the 2 bolts. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} HINT: Tighten the bolts in the order shown in the illustration.

(d) Connect the connector.

(e) Engage the clamp.

3. INSTALL WATER GUARD PLATE

(a) Engage the clamp to install the water guard plate.

4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

(a) Align the protrusion of the cowl top ventilator louver sub-assembly and engage the 3 guides to temporarily install the cowl top ventilator louver sub-assembly as shown in the illustration.

*a	Guide	-	-
	Install in this Direction	-	-

NOTICE:

Make sure that the cowl top ventilator louver sub-assembly does not contact the vehicle body, otherwise it may be damaged.

(b) Engage the cowl top ventilator louver sub-assembly to the windshield glass as shown in the illustration.

Install in this Direction

-

-

NOTICE:

Make sure to engage the guide securely, otherwise the cowl top ventilator louver sub-assembly may pop up when engaging it to the windshield glass.

(c) Engage the 4 clips as shown in the illustration.

Install in this Direction

-

-

5. INSTALL COWL WATER EXTRACT SHIELD LH

(a) Engage the cowl water extract shield LH to the windshield glass.

(b) Engage the guide and 2 claws to install the cowl water extract shield LH.

6. INSTALL COWL WATER EXTRACT SHIELD RH

HINT:

Use the same procedure as for the LH side.

7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

(a) When reusing the front wiper arm and blade assembly RH:

(1) Clean the wiper arm serrations to remove any burrs, dirt, etc. NOTICE: Do not grind down the wiper arm serrations.

*a Serration

(b) When reusing the windshield wiper motor and link assembly:

(1) Clean the wiper pivot serrations with a wire brush.

(c) Turn the engine switch on (IG).

(d) Operate the windshield wiper motor assembly and stop the windshield wiper motor and link assembly at the automatic stop position.

(e) Turn the engine switch off.

(f) Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration. Torque: 23 N·m {235 kgf·cm, 17 ft·lbf} HINT: Hold the wiper arm by hand while tightening the nut. Reference Measurement: Area Measurement A 10 mm (0.394 in.)

*a Alignment Mark

8. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

(a) When reusing the front wiper arm and blade assembly LH:

(1) Clean the wiper arm serrations to remove any burrs, dirt, etc. NOTICE: Do not grind down the wiper arm serrations.

*a Serration

(b) When reusing the windshield wiper motor and link assembly:

(1) Clean the wiper pivot serrations with a wire brush.

(c) Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration. Torque: 23 N·m {235 kgf·cm, 17 ft·lbf} HINT: Hold the wiper arm by hand while tightening the nut. Reference Measurement: Area Measurement A 10 mm (0.394 in.)

*a Alignment Mark

(d) Turn the engine switch on (IG).

(e) Operate the windshield wipers while spraying washer fluid onto the windshield glass. Make sure that the windshield wipers function properly and the wipers do not contact the vehicle body.

(f) Turn the engine switch off.

(g) Lift each wiper arm twice after the wipers stop and check the wiper set position.

9. INSTALL FRONT WIPER ARM HEAD CAP

(a) Engage the 3 claws to install the front wiper arm head cap. HINT: Use the same procedure for the RH side and LH side.