| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CW5J |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: MAINTENANCE: REAR DISC BRAKE PAD (w/ Electric Parking Brake): INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] | ||
INSTALLATION
CAUTION / NOTICE / HINT
NOTICE:
- Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
- After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.
- After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT
NOTICE:
- When replacing worn rear disc brake pads, the rear disc brake anti-squeal shims and rear disc brake pad wear indicator plates must be replaced together with the rear disc brake pads.
- Install each rear disc brake pad wear indicator plate in the correct position and direction.
- Install the rear disc brake anti-squeal shims in the correct positions and directions.
|
(a) Check the rear disc brake pad. HINT: If the rear disc brake pad has an identification mark, be sure to confirm the installation location. |
|
|
(b) Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad. |
|
(c) Install a new rear disc brake pad wear indicator plate to each rear disc brake pad.
2. INSTALL REAR DISC BRAKE PAD
CAUTION:
- Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.
- After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.
- The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.
(a) Push in the rear disc brake piston.
NOTICE:
- Make sure the brake fluid does not overflow from the reservoir.
- Do not forcibly push in the rear disc brake piston.
(b) Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.
NOTICE:
- Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.
- Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.
HINT:
If the rear disc brake pad has an identification mark, be sure to confirm the installation location.
|
*a |
Inner Side (Green) |
|
*b |
Outer Side (Orange) |
(c) Hold the rear No. 1 disc brake cylinder slide pin and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with a new bolt.
Torque:
34.3 N·m {350 kgf·cm, 25 ft·lbf}
(d) Depress the brake pedal and release it.
3. CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
Click here
![2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - ]; PARKING BRAKE: ELECTRIC PARKING BRAKE ACTUATOR: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
4. INSPECT BRAKE FLUID LEVEL IN RESERVOIR
Click here
5. INSTALL REAR WHEEL
Click here
6. NORMAL CONDITION RECOVERY
Click here
|
|