Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001CW55
Model Year Start: 2019 Model: Corolla Hatchback Prod Date Range: [06/2018 - 01/2019]
Title: DRIVE SHAFT / PROPELLER SHAFT: FRONT DRIVE SHAFT ASSEMBLY (for M20A-FKS): REMOVAL; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front wheel alignment adjustment
  1. Perform "Reset Memory".
  2. Perform acceleration sensor zero point calibration and store system information memorization.
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): UTILITY

CVT fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly

2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT WHEELS

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; MAINTENANCE: TIRE AND WHEEL: REMOVAL+

2. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

3. REMOVE REAR ENGINE UNDER COVER LH

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE REAR ENGINE UNDER COVER RH

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Click here 2019 - 2023 MY Corolla Corolla Hatchback [06/2018 - 11/2022]; MAINTENANCE: EG60 MANUAL TRANSAXLE OIL: REPLACEMENT+

6. DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; K120 / K121 (CVT): OIL PAN: REMOVAL+

7. REMOVE FRONT AXLE SHAFT NUT

(a) Using SST and a hammer, release the staked part of the front axle shaft nut.

SST: 09930-00010

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.

(b) While applying the brakes, remove the front axle shaft nut.

8. SEPARATE FRONT SPEED SENSOR

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB (except G16E-GTS): REMOVAL+

9. SEPARATE TIE ROD END SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; STEERING GEAR / LINKAGE: STEERING GEAR: REMOVAL+

10. SEPARATE FRONT STABILIZER LINK ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; FRONT SUSPENSION: FRONT SHOCK ABSORBER (except G16E-GTS): REMOVAL+

11. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB (except G16E-GTS): REMOVAL+

12. SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB (except G16E-GTS): REMOVAL+

13. REMOVE FRONT DRIVE SHAFT ASSEMBLY

(a) Using SST, remove the front drive shaft assembly.

SST: 09520-01011

SST: 09520-20010

09521-02010

09521-02040

09521-02060

NOTICE:

  • Do not damage the front drive shaft oil seal LH.
  • Do not damage the front axle inboard joint boot.
  • Do not drop the front drive shaft assembly.

14. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

(a) Using a screwdriver, remove the front drive shaft hole snap ring.