| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CVTC |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: REAR SUSPENSION: REAR SHOCK ABSORBER: INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] | ||
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL REAR SUSPENSION SUPPORT ASSEMBLY
(a) Secure the rear suspension support assembly in a vise using aluminum plates.
NOTICE:
Do not overtighten the vise.
(b) Install the rear suspension support assembly to the rear shock absorber assembly.
(c) Apply a few drops of adhesive to the threads of a new rear support to rear shock absorber nut.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
|
(d) Using SST and a 6 mm hexagon socket wrench, hold the rear shock absorber rod and tighten the rear support to rear shock absorber nut. SST: 09729-97202 Torque: Specified tightening torque : 25 N·m {255 kgf·cm, 18 ft·lbf} NOTICE: Securely insert the 6 mm hexagon socket wrench into the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the rear support to rear shock absorber nut. HINT:
|
|
2. INSTALL REAR SHOCK ABSORBER CAP
(a) Install the rear shock absorber cap to the rear shock absorber assembly.
3. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY
|
(a) Temporarily install the rear shock absorber assembly to the rear axle carrier sub-assembly with the nut and plate washer. NOTICE: Hold the rear axle carrier pin while rotating the nut. |
|
4. STABILIZE SUSPENSION
(a) Using a jack and a wooden block, apply load to the suspension so that the rear No. 2 suspension arm assembly is positioned as shown in the illustration.
Standard Length (A):
13 mm (0.512 in.)
CAUTION:
Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.
NOTICE:
- When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.
- Make sure to perform this operation with the vehicle kept as low as possible.
|
*a |
Wooden Block |
|
*b |
Jack |
|
Wooden Block Placement Location |
5. INSTALL REAR UPPER CONTROL ARM ASSEMBLY
(a) Install the rear upper control arm assembly to the rear axle carrier sub-assembly with the bolt and nut.
Torque:
73 N·m {744 kgf·cm, 54 ft·lbf}
NOTICE:
- Insert the bolt with the threaded end facing the rear of the vehicle.
- Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.
6. CONNECT REAR SHOCK ABSORBER ASSEMBLY
|
(a) Connect the rear shock absorber assembly to the vehicle with the 2 bolts. Torque: 55 N·m {561 kgf·cm, 41 ft·lbf} NOTICE: Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A). |
|
7. INSTALL REAR SHOCK ABSORBER ASSEMBLY
|
(a) Using a ball joint lock nut wrench fully tighten the rear shock absorber assembly with the nut. Torque: Specified tightening torque : 125 N·m {1275 kgf·cm, 92 ft·lbf} NOTICE: Hold the rear axle carrier pin while rotating the nut. HINT:
|
|
8. INSTALL REAR STABILIZER LINK ASSEMBLY
Click here
![2019 - 2020 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2019]; REAR SUSPENSION: REAR STABILIZER BAR (for Hatchback): INSTALLATION+](/t3Portal/stylegraphics/info.gif)
9. INSTALL REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)
(a) for LH Side:
Click here
10. INSTALL REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)
(a) for RH Side:
Click here
11. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)
(a) for LH Side:
Click here
12. INSTALL REAR WHEEL
Click here
13. INSPECT AND ADJUST REAR WHEEL ALIGNMENT
Click here
14. PERFORM INITIALIZATION
|
Lighting System (w/ AFS) (EXT) |
|
|
|