Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001CVOF
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING UNIT: INSTALLATION; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]

INSTALLATION

PROCEDURE

1. TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

(a) Engage the 2 claws.

(b) Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:

  • Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
  • When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

(a) Engage the 2 guides and claw to connect the ID code box (immobiliser code ECU) as shown in the illustration.

Install in this Direction

(b) Connect each connector.

Install in this Direction

-

-

(c) Engage each clamp.

(d) Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

(e) Install the 4 bolts (A).

*A

for Manual Transaxle

-

-

Bolt (A)

Bolt (B)

Bolt (C)

Nut

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

(f) Install the bolt (B).

Torque:

23.6 N·m {241 kgf·cm, 17 ft·lbf}

(g) Install the bolt (C).

Torque:

15 N·m {153 kgf·cm, 11 ft·lbf}

(h) Temporarily install the nut.

(i) Install the 2 bolts.

Torque:

25 N·m {255 kgf·cm, 18 ft·lbf}

(j) Install a new cooler unit drain hose grommet.

NOTICE:

  • If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.
  • Make sure that the entire lip of the cooler unit drain hose grommet is securely engaged to the vehicle body.

*a

Lip

(k) Connect the drain cooler hose.

(l) Install the front floor mat to its original position as shown in the illustration.

3. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

(a) Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:

Bolt :

20 N·m {204 kgf·cm, 15 ft·lbf}

Nut :

18 N·m {184 kgf·cm, 13 ft·lbf}

(b) Temporarily install the screw.

HINT:

Do not fully tighten the screw.

(c) Engage each clamp.

(d) Install the front floor mat to its original position as shown in the illustration.

Move in this Direction

4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

(a) Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:

Bolt :

20 N·m {204 kgf·cm, 15 ft·lbf}

Nut :

18 N·m {184 kgf·cm, 13 ft·lbf}

(b) Temporarily install the screw.

HINT:

Do not fully tighten the screw.

(c) Engage each clamp.

(d) Connect the earth wire with the bolt.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

(e) Install the front floor mat to its original position as shown in the illustration.

Move in this Direction

5. INSTALL AIR CONDITIONER UNIT ASSEMBLY

(a) Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

Bolt

Screw

Nut

-

-

Torque:

Bolt :

9.8 N·m {100 kgf·cm, 87 in·lbf}

Nut :

9.8 N·m {100 kgf·cm, 87 in·lbf}

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.

6. CONNECT INSTRUMENT PANEL WIRE

(a) Engage each clamp.

*a

Lock Lever

Move in this Direction

(b) Temporarily connect the connector and then move the lock lever as shown in the illustration to securely connect the connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

(c) Check that there is no looseness in the installed parts of the airbag sensor assembly.

(d) Engage each clamp.

(e) Connect the instrument panel wire with the screw.

Torque:

3.2 N·m {33 kgf·cm, 28 in·lbf}

(f) Connect the 3 earth wires with the 3 bolts.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

(g) Connect the connector.

(h) Connect the instrument panel wire with the bolt.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(i) Connect the relay block holder with the 2 nuts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

7. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; POWER DISTRIBUTION: MAIN BODY ECU: INSTALLATION+

8. INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

(a) Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.

Torque:

Bolt :

10 N·m {102 kgf·cm, 7 ft·lbf}

Nut :

6.0 N·m {61 kgf·cm, 53 in·lbf}

9. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

(a) Engage the guide and 6 claws to install the lower defroster nozzle assembly.

10. INSTALL CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

(a) Install the center heater to register duct sub-assembly with the 2 clips.

(b) Engage the clamp.

11. INSTALL NO. 3 DASH PANEL INSULATOR PAD

(a) Install the No. 3 dash panel insulator pad with 2 new clips as shown in the illustration.

12. INSTALL REAR NO. 2 AIR DUCT

(a) Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.

Install in this Direction

13. INSTALL REAR NO. 5 AIR DUCT

(a) Engage the 2 claws to install the rear No. 5 air duct as shown in the illustration.

Install in this Direction

14. INSTALL REAR NO. 6 AIR DUCT

(a) Engage the 2 claws to install the rear No. 6 air duct as shown in the illustration.

Install in this Direction

15. INSTALL REAR NO. 3 AIR DUCT

Install in this Direction

(a) Engage the 2 claws to install the rear No. 3 air duct as shown in the illustration.

16. INSTALL REAR NO. 4 AIR DUCT

(a) Engage the 2 claws to install the rear No. 4 air duct as shown in the illustration.

Install in this Direction

17. CONNECT FRONT FLOOR CARPET ASSEMBLY

(a) for LH Side:

(1) Install the front floor carpet assembly to its original position as shown in the illustration.

(2) Engage the 2 guides.

(3) Install the 3 front floor carpet clips.

(b) for RH Side:

(1) Install the front floor carpet assembly to its original position as shown in the illustration.

(2) Engage the 2 guides.

(3) Install the 3 front floor carpet clips.

18. INSTALL FRONT FLOOR CAUTION PLATE COVER

(a) Engage the guide and claw to install the front floor caution plate cover as shown in the illustration.

Install in this Direction (1)

Install in this Direction (2)

19. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; DOOR / HATCH: FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback): INSTALLATION+

20. INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR

(a) Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.

21. INSTALL METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; METER / GAUGE / DISPLAY: HEADUP DISPLAY: INSTALLATION+

22. INSTALL ECU INTEGRATION BOX RH

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; NETWORKING: NETWORK GATEWAY ECU: INSTALLATION+

23. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: INSTALLATION

24. INSTALL STEERING COLUMN ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

25. INSTALL FRONT SEAT ASSEMBLY LH

for Manual Seat:

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): INSTALLATION

for Power Seat:

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SEAT: FRONT SEAT ASSEMBLY (for Power Seat): INSTALLATION

26. INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

27. CONNECT SUCTION PIPE SUB-ASSEMBLY

(a) Remove the vinyl tape from the suction pipe sub-assembly.

(b) Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 12 or equivalent

(c) Install the 2 O-rings to the suction pipe sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.

(d) Connect the suction pipe sub-assembly.

(e) Rotate the hook connector as shown in the illustration.

(f) Insert the tube joint into the fitting hole securely and temporarily install the bolt.

(g) Using a union nut wrench, tighten the bolt.

Torque:

Specified tightening torque :

9.8 N·m {100 kgf·cm, 87 in·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    8.6 N*m (88 kgf*cm, 76 in.*lbf)

*a

Torque Wrench Fulcrum Length

*b

Union Nut Wrench

28. CONNECT INLET HEATER WATER HOSE

(a) Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.

*a

View A

*b

Marking (Green)

*c

Clip Installation Angle (90°)

*d

Clip Installation Angle (120°)

29. CONNECT OUTLET HEATER WATER HOSE

(a) Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose.

*a

View A

*b

Marking (Green)

*c

Clip Installation Angle (90°)

*d

Clip Installation Angle (120°)

30. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; FRONT SUSPENSION: FRONT SHOCK ABSORBER (except G16E-GTS): INSTALLATION+

31. INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; FRONT SUSPENSION: FRONT SHOCK ABSORBER (except G16E-GTS): INSTALLATION+

32. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; WIPER / WASHER: FRONT WIPER MOTOR: INSTALLATION

33. ADD ENGINE COOLANT

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; MAINTENANCE: M20A-FKS COOLANT: REPLACEMENT+

34. INSPECT FOR COOLANT LEAK

Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; MAINTENANCE: M20A-FKS COOLANT: REPLACEMENT+

35. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

36. WARM UP ENGINE

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

37. INSPECT FOR REFRIGERANT LEAK

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+