Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001CVOE
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING UNIT: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION

NOTICE:

  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) battery terminal.

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; HEATING / AIR CONDITIONING: REFRIGERANT (for HFO-1234yf(R1234yf)): REPLACEMENT+

3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; WIPER / WASHER: FRONT WIPER MOTOR: REMOVAL

4. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; FRONT SUSPENSION: FRONT SHOCK ABSORBER (except G16E-GTS): REMOVAL+

5. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV [06/2018 - 01/2019]; FRONT SUSPENSION: FRONT SHOCK ABSORBER (except G16E-GTS): REMOVAL+

6. DISCONNECT OUTLET HEATER WATER HOSE

(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose.

NOTICE:

  • Do not apply excessive force to the outlet heater water hose.
  • Prepare a drain pan or cloth in case the coolant leaks.

7. DISCONNECT INLET HEATER WATER HOSE

(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose.

NOTICE:

  • Do not apply excessive force to the inlet heater water hose.
  • Prepare a drain pan or cloth in case the coolant leaks.

8. DISCONNECT SUCTION PIPE SUB-ASSEMBLY

(a) Remove the bolt and rotate the hook connector as shown in the illustration.

(b) Disconnect the suction pipe sub-assembly.

(c) Remove the 2 O-rings from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

9. REMOVE FRONT SEAT ASSEMBLY LH

for Manual Seat:

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REMOVAL

for Power Seat:

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; SEAT: FRONT SEAT ASSEMBLY (for Power Seat): REMOVAL

10. REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

11. REMOVE STEERING COLUMN ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: REMOVAL

12. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL

13. REMOVE ECU INTEGRATION BOX RH

Click here 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022]; NETWORKING: NETWORK GATEWAY ECU: REMOVAL+

14. REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; METER / GAUGE / DISPLAY: HEADUP DISPLAY: REMOVAL+

15. REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR

(a) Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.

16. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; DOOR / HATCH: FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback): REMOVAL+

17. REMOVE FRONT FLOOR CAUTION PLATE COVER

(a) Lift the front floor caution plate cover as shown by the arrow (1) to disengage the claw, and then pull the front floor caution plate cover as shown by the arrow (2) in the illustration to disengage the guide and remove it.

Place Hand Here

Remove in this Direction (1)

Remove in this Direction (2)

18. DISCONNECT FRONT FLOOR CARPET ASSEMBLY

(a) for LH Side:

(1) Remove the front floor carpet clip.

(2) Remove the 2 front floor carpet clips.

(3) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.

(b) for RH Side:

(1) Remove the front floor carpet clip.

(2) Remove the 2 front floor carpet clips.

(3) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration.

19. REMOVE REAR NO. 4 AIR DUCT

(a) Disengage the 2 claws and remove the rear No. 4 air duct as shown in the illustration.

Remove in this Direction

20. REMOVE REAR NO. 3 AIR DUCT

Remove in this Direction

(a) Disengage the 2 claws and remove the rear No. 3 air duct as shown in the illustration.

21. REMOVE REAR NO. 6 AIR DUCT

(a) Disengage the 2 claws and remove the rear No. 6 air duct as shown in the illustration.

Remove in this Direction

22. REMOVE REAR NO. 5 AIR DUCT

(a) Disengage the 2 claws and remove the rear No. 5 air duct as shown in the illustration.

Remove in this Direction

23. REMOVE REAR NO. 2 AIR DUCT

(a) Disengage the 4 claws and remove the rear No. 2 air duct as shown in the illustration.

Remove in this Direction

24. REMOVE NO. 3 DASH PANEL INSULATOR PAD

(a) Cut each claw of the 2 clips and remove the No. 3 dash panel insulator pad.

NOTICE:

If the No. 3 dash panel insulator pad is damaged, replace it with a new one.

*a

Cut

(b) Remove the 2 clips.

25. REMOVE CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

(a) Disengage the clamp.

(b) Remove the 2 clips and center heater to register duct sub-assembly.

26. REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

(a) Disengage the 6 claws and guide to remove the lower defroster nozzle assembly.

27. REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

(a) Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.

Bolt

Nut

28. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL+

29. DISCONNECT INSTRUMENT PANEL WIRE

(a) Remove the 2 nuts and disconnect the relay block holder.

(b) Remove the bolt and disconnect the instrument panel wire.

(c) Disconnect the connector.

*a

Earth Wire

-

-

Connector

Bolt

Screw

-

-

(d) Remove the 3 bolts and disconnect the 3 earth wires.

(e) Remove the screw and disconnect the instrument panel wire.

(f) Disengage each clamp.

(g) Push down the part (A) in the direction indicated by the arrow (1), to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connector.

Release (1)

Move in this Direction (2)

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(h) Disengage each clamp to separate the instrument panel wire.

30. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

(a) Turn back the front floor mat as shown in the illustration.

Move in this Direction

(b) Remove the bolt and disconnect the earth wire.

*a

Earth Wire

(c) Disengage each clamp.

(d) Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.

Bolt

Screw

Nut

31. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

(a) Turn back the front floor mat as shown in the illustration.

Move in this Direction

(b) Disengage each clamp.

(c) Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.

Bolt

Screw

Nut

32. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:

  • Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
  • When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.

(a) Turn back the front floor mat as shown in the illustration.

(b) Disconnect the drain cooler hose.

NOTICE:

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.

*1

Cooler Unit Drain Hose Grommet

(c) Remove the cooler unit drain hose grommet.

(d) Remove the 2 bolts.

(e) Remove the 4 bolts (A).

*A

for Manual Transaxle

-

-

Bolt (A)

Bolt (B)

Bolt (C)

Nut

(f) Remove the bolt (B).

(g) Remove the bolt (C).

(h) Remove the nut.

(i) Disengage each clamp.

Remove in this Direction

-

-

(j) Disconnect each connector.

(k) Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

(l) Disengage the claw and 2 guides to disconnect the ID code box (immobiliser code ECU) as shown in the illustration.

Remove in this Direction

33. REMOVE AIR CONDITIONER UNIT ASSEMBLY

(a) Remove the 3 bolts.

(b) Disengage the 2 claws and remove the air conditioner unit assembly from the instrument panel reinforcement assembly.