| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001CVGJ |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: AUDIO / VIDEO: RADIO ANTENNA CORD (for Hatchback): REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during antenna cord sub-assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Control System |
|
|
Pre-collision System |
|||
|
Lighting System (w/ AFS)(EXT) |
|||
|
Initialize back door lock |
Power Door Lock Control System |
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
- After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here
2. REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here
3. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY
(a) w/o Manual (SOS) Switch:
(1) Disconnect the connector and disengage the 2 claws.
(2) Disengage the 6 clamps and remove the No. 2 antenna cord sub-assembly.
(b) w/ Manual (SOS) Switch:
(1) Disconnect the connector and disengage the 2 claws.
(2) Disengage the 9 clamps and remove the No. 2 antenna cord sub-assembly.
4. REMOVE ROOF HEADLINING ASSEMBLY
Click here
5. REMOVE NO. 1 ROOF SILENCER PAD
Click here
6. REMOVE NO. 2 ROOF SILENCER PAD
Click here
7. REMOVE ANTENNA CORD SUB-ASSEMBLY
(a) Remove the adhesive tape from the roof headlining assembly.
|
Adhesive Tape |
- |
- |
(b) Remove the antenna cord sub-assembly from the roof headlining assembly.
8. REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER
Click here
9. REMOVE ANTENNA CORD SUB-ASSEMBLY
|
(a) Disconnect the washer hose. HINT: Use a container to collect the windshield washer fluid. |
|
(b) Disengage the 2 clamps.
|
(c) Disconnect the connector. |
|
(d) Disengage the 4 clamps.
|
(e) Disconnect the washer hose. HINT: Use a container to collect the windshield washer fluid. |
|
|
(f) Disengage the 8 claws to separate the 2 grommets. |
|
(g) Remove the antenna cord sub-assembly.
|
|