| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CURE |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: CRUISE CONTROL: FRONT CAMERA SYSTEM (for Gasoline Model): U030057; Internal Control Module Software Incompatibility Invalid / Incompatible Software Component; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019] | ||
|
DTC |
U030057 |
Internal Control Module Software Incompatibility Invalid / Incompatible Software Component |
DESCRIPTION
Forward recognition camera receives the vehicle information from the ECM via CAN communication.
DTC U030057 is stored when the vehicle information from the ECM and that stored in the forward recognition camera do not match.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U030057 |
Internal Control Module Software Incompatibility Invalid / Incompatible Software Component |
The vehicle information from the ECM and that stored in the forward recognition camera do not match. |
|
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
-
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; CRUISE CONTROL: FRONT CAMERA: ADJUSTMENT (ONE TIME RECOGNITION)](/t3Portal/stylegraphics/info.gif)
Sequential Recognition: Click here
PROCEDURE
|
1. |
CHECK FOR DTCs |
(a) Check for DTCs of SFI system.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output |
A |
|
DTCs are output |
B |
| B |
|
|
|
2. |
CHECK FOR DTCs (HEALTH CHECK) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG)
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Health Check.
(e) Check for DTCs.
(f) Turn the engine switch off.
OK:
DTCs indicating a vehicle information mismatch with that of the ECM are not output by any ECU other than the forward recognition camera.
| NG |
|
|
|
3. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG)
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Front Recognition Camera / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Front Recognition Camera > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
HV Equipped Information |
Vehicle information (conventional/hybrid) stored in forward recognition camera |
Non-HV / HV |
Non-HV: Conventional vehicle HV: Hybrid vehicle |
- |
Chassis > Front Recognition Camera > Data List
|
Tester Display |
|---|
|
HV Equipped Information |
HINT:
- If the vehicle information stored in the forward recognition camera is different from the actual vehicle specifications, the vehicle information stored in the forward recognition camera may be incorrect. Replace the forward recognition camera.
- If the vehicle information stored in the forward recognition camera matches the actual vehicle specifications, the installed ECM is incompatible. Replace the ECM.
|
Result |
Proceed to |
|---|---|
|
Vehicle information stored in forward recognition camera and actual vehicle specifications do not match |
A |
|
Vehicle information stored in forward recognition camera and actual vehicle specifications match |
B |
| A |
|
| B |
|
|
|