- Open in CAN communication line (forward recognition camera - CAN junction connector)
- Open in CAN communication line (millimeter wave radar sensor assembly - CAN junction connector)
- CAN junction connector disconnected
- CAN junction connector
- Short in CAN communication line
- Open or short in forward recognition camera internal circuit
- Open or short in millimeter wave radar sensor assembly internal circuit
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CUQI |
| Model Year Start: 2019 | Model: GR Corolla | Prod Date Range: [06/2018 - 01/2019] |
| Title: CRUISE CONTROL: FRONT RADAR SENSOR SYSTEM (for Gasoline Model): U010487; Lost Communication with Cruise Control Module Missing Message; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019] | ||
|
DTC |
U010487 |
Lost Communication with Cruise Control Module Missing Message |
DESCRIPTION
The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.
If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
|---|---|---|---|---|
|
U010487 |
Lost Communication with Cruise Control Module Missing Message |
Detection condition:
Malfunction status:
Malfunction duration:
|
|
Millimeter wave radar sensor assembly |
|
Pattern |
DTC output part name (Display on Techstream) |
Suspected Area (Malfunction Status) |
|
|---|---|---|---|
|
Millimeter Wave Radar Sensor Assembly (Front Radar Sensor) |
Forward Recognition Camera (Pre-Collision System) |
||
|
U010487 |
U023587 |
||
|
○: DTC is output.
-: DTC is not output |
|||
|
Pattern 1 |
○ |
○ |
|
|
Pattern 2 |
○ |
- |
|
HINT:
If the DTCs are output simultaneously, the inspection area can be narrowed down.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
![2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
-
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the millimeter wave radar sensor beam axis must be performed.
Click here
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
-
If the forward recognition camera has been replaced with a new one, forward recognition camera adjustment must be performed.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.
One Time Recognition: Click here
Sequential Recognition: Click here
PROCEDURE
|
1. |
CHECK FOR DTCs |
(a) Check for pre-collision system DTCs.
Body Electrical > Pre-Collision System > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC U023587 is output |
A |
|
DTC U023587 is not output |
B |
| B |
|
|
|
2. |
CHECK CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I108 No. 2 CAN junction connector.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to No. 2 CAN Junction Connector) |
*b |
to Forward Recognition Camera |
|
*c |
to Millimeter Wave Radar Sensor Assembly |
- |
- |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
Connected to |
|---|---|---|---|
|
I108-6 - I108-17 |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
Forward Recognition Camera |
|
I108-4 - I108-15 |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
Millimeter Wave Radar Sensor Assembly |
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
Connected to |
|---|---|---|---|
|
I108-6 - I26-4(CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
Forward Recognition Camera |
|
I108-17 - I26-4(CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
|
I108-6 - I26-16(BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
|
I108-17 - I26-16(BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
|
I108-4 - I26-4(CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
Millimeter Wave Radar Sensor Assembly |
|
I108-15 - I26-4(CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
|
I108-4 - I26-16(BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
|
I108-15 - I26-16(BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
(e) Connect the I108 No. 2 CAN junction connector.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (Connected to: Forward Recognition Camera) |
B |
|
NG (Connected to: Millimeter Wave Radar Sensor Assembly) |
C |
| A |
|
REPLACE NO. 2 CAN JUNCTION CONNECTOR |
| C |
|
|
|
3. |
CHECK CAN BUS LINES (FORWARD RECOGNITION CAMERA - NO. 2 CAN JUNCTION CONNECTOR) |
(a) Disconnect the T9 forward recognition camera connector.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to Forward Recognition Camera) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
T9-6 (CANH) - T9-12 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132Ω |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
T9-6 (CANH) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
T9-12 (CANL) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
T9-6 (CANH) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
T9-12 (CANL) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
(d) Connect the T9 forward recognition camera connector.
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (FORWARD RECOGNITION CAMERA - NO. 2 CAN JUNCTION CONNECTOR) |
|
4. |
CHECK CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR) |
(a) Disconnect the A1 millimeter wave radar sensor assembly connector.
|
*1 |
DLC3 |
- |
- |
|
*a |
Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A1-5 (CA1P) - A1-6 (CA1N) |
Cable disconnected from negative (-) battery terminal |
108 to 132Ω |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A1-5 (CA1P) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
A1-6 (CA1N) - I26-4 (CG) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
|
A1-5 (CA1P) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
|
A1-6 (CA1N) - I26-16 (BAT) |
Cable disconnected from negative (-) battery terminal |
6 kΩ or higher |
(d) Connect the A1 millimeter wave radar sensor assembly connector.
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR) |
|
5. |
CHECK CONNECTOR (FORWARD RECOGNITION CAMERA) |
(a) Check the locking part and terminals of the forward recognition camera connector.
NOTICE:
- Make sure the connector is not loose or disconnected.
- Make sure that the connector and terminals are not deformed or corroded.
OK:
The connector and terminals are normal.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION CAMERA) |
|
|
6. |
CHECK HARNESS AND CONNECTOR (FORWARD RECOGNITION CAMERA POWER SOURCE CIRCUIT) |
(a) Disconnect the cable from the negative (-) battery terminal.
|
(b) Disconnect the T9 forward recognition camera connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
T9-10 (GND) - Body ground |
Always |
Below 1 Ω |
(d) Connect the cable to the negative (-) battery terminal.
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
T9-7 (IGB) - Body ground |
Engine switch on (IG) |
11 to 14 V |
(f) Connect the T9 forward recognition camera connector.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (FORWARD RECOGNITION CAMERA POWER SOURCE CIRCUIT) |
|
|
7. |
INSPECT FORWARD RECOGNITION CAMERA (WAVEFORM) |
(a) Turn the engine switch off.
(b) Disconnect the I108 No. 2 CAN junction connector.
(c) Turn the engine switch on (IG).
(d) Using an oscilloscope, measure the waveform at I108 No. 2 CAN junction connector.
|
*a |
Front view of wire harness connector (to No. 2 CAN Junction Connector) |
*b |
Waveform |
|
*c |
to Forward Recognition Camera |
- |
- |
Measurement Condition:
|
Tester Connection |
Condition |
Tool Setting |
|---|---|---|
|
I108-6 - Body ground |
Engine switch on (IG) |
1 V/DIV., 100 μs/DIV. |
NOTICE:
The oscilloscope waveform is for reference only and does not include noise, fluctuations, etc.
OK:
A waveform similar to that in the illustration can be observed.
(e) Connect the I108 No. 2 CAN junction connector.
| OK |
|
| NG |
|
|
|