| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM100000001CUP9 |
| Model Year Start: 2019 | Model: Corolla Hatchback | Prod Date Range: [06/2018 - 01/2019] |
| Title: CRUISE CONTROL: DYNAMIC RADAR CRUISE CONTROL SYSTEM (for M20A-FKS): DATA LIST / ACTIVE TEST; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019] | ||
DATA LIST / ACTIVE TEST
NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
- When diagnosing symptoms such as hesitation, rough idle, or other small symptoms using vehicle control history, compare data extracted from the same vehicle model in the same conditions and make sure to analyze all data in its entirety before making a diagnosis.
DATA LIST
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Radar Cruise 1*1 or Radar Cruise 2*2 / Data List.
- *1: Output from the ECM
- *2: Output from the forward recognition camera
(e) Radar Cruise 1:
Read the Data List according to the display on the Techstream.
Powertrain > Radar Cruise1 > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Cruise Vehicle Speed |
Vehicle speed |
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Actual vehicle speed |
- |
|
Cruise Memory Vehicle Speed |
Stored vehicle speed |
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Stored vehicle speed |
- |
|
Cruise Request Throttle Opening Angle |
Cruise requested position |
0 to 124.99 deg |
Changes depending on the conditions of the dynamic radar cruise control system |
- |
|
Vehicle Acceleration |
Acceleration condition while driving the vehicle |
-13.10 to 13.10 m/s2 |
Current value displayed |
- |
|
Cruise Target Acceleration |
Target acceleration while in cruise control mode |
-13.10 to 13.10 m/s2 |
Current value displayed |
- |
|
Driving Support ECU Target Acceleration |
- |
- |
- |
Cannot be used |
|
Acceleration Continuation Decision |
- |
- |
- |
Cannot be used |
|
Output Driving Force |
- |
- |
- |
Cannot be used |
|
Cruise Request Driving Force |
Cruise request torque signal |
-10.00 to 9.92 kN |
Changes depending on the conditions of the dynamic radar cruise control system |
- |
|
Cruise Request Driving Force Feedback Status |
- |
- |
- |
Cannot be used |
|
Cruise Control Permission Condition |
- |
- |
- |
Cannot be used |
|
Cruise Control Condition |
- |
- |
- |
Cannot be used |
|
Cruise Control Mode |
Cruise control mode condition |
Vehicle Distance Control Mode (All Speed), Vehicle Distance Control Mode or Constant Speed Control Mode |
Vehicle Distance Control Mode (All Speed): Vehicle distance control mode (All Speed) operating Vehicle Distance Control Mode: Vehicle distance control mode operating Constant Speed Control Mode: Constant speed control mode operating |
- |
|
Cruise Request Gear Position |
Shift request from ECM |
None or 255 Gear |
Shift request from cruise control system |
- |
|
Cruise Acceleration and Deceleration Operation Condition |
- |
- |
- |
Cannot be used |
|
Cancel Switch |
CANCEL switch status |
ON or OFF |
ON: CANCEL switch pushed OFF: CANCEL switch not pushed |
- |
|
-SET Switch |
-SET switch status |
ON or OFF |
ON: -SET switch pushed OFF: -SET switch not pushed |
- |
|
+RES Switch |
+RES switch status |
ON or OFF |
ON: +RES switch pushed OFF: +RES switch not pushed |
- |
|
Cruise Main Switch Operation Condition |
Cruise control main switch status |
ON or OFF |
ON: Cruise control main switch pushed OFF: Cruise control main switch not pushed |
- |
|
Cruise Ready Main-CPU |
Cruise control system standby condition |
ON or OFF |
ON: Cruise control main switch pushed OFF: Cruise control main switch not pushed |
- |
|
Cruise Ready Sub-CPU |
Cruise control system standby condition |
ON or OFF |
ON: Cruise control main switch pushed OFF: Cruise control main switch not pushed |
- |
|
Accelerator Pedal |
Condition of the accelerator pedal during cruising |
ON or OFF |
ON: Accelerator pedal depressed OFF: Accelerator pedal released |
- |
|
Cruise Brake Cancel Switch |
Cruise control brake cancel condition |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
|
Stop Light Switch Main-CPU |
Stop light switch signal |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
|
Stop Light Switch Sub-CPU |
- |
- |
- |
Cannot be used |
|
Request Manual Cancel |
- |
- |
- |
Cannot be used |
|
Request Automatic Cancel |
- |
- |
- |
Cannot be used |
|
Cruise Brake Control Decision |
Cruise brake control decision |
ON or OFF |
ON: Cruise brake activated OFF: Cruise brake deactivated |
- |
|
Cruise Brake Control Permission Condition |
- |
- |
- |
Cannot be used |
|
Cruise Indicator |
Cruise control indicator status |
ON or OFF |
ON: Cruise control indicator illuminates OFF: Cruise control indicator turns off |
- |
|
Wheel Speed Sensor and Deceleration Sensor |
Speed sensor signal and deceleration sensor signal condition |
Avail or Not Avl |
Avail: Speed sensor signal and deceleration sensor signal available Not Avl: Speed sensor signal and deceleration sensor signal not available |
- |
|
Gradient of Road Surface |
- |
- |
- |
Cannot be used |
(f) Radar Cruise 2:
Read the Data List according to the display on the Techstream.
Powertrain > Radar Cruise2 > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Total Distance Traveled |
- |
- |
- |
Cannot be used |
|
Total Distance Traveled - Unit |
- |
- |
- |
Cannot be used |
|
Cruise Control Main Switch |
Cruise control main switch status |
ON or OFF |
ON: Cruise control main switch pushed OFF: Cruise control main switch not pushed |
- |
|
Vehicle-to-vehicle Distance Control Switch |
Vehicle-to-vehicle distance control switch signal |
ON or OFF |
ON: Vehicle-to-vehicle distance control switch pushed OFF: Vehicle-to-vehicle distance control switch not pushed |
- |
|
Cruise Control Mode |
Cruise control mode signal |
Vehicle-to-vehicle Distance Control (All Speed), Vehicle-to-vehicle Distance Control (Hi Speed) or Constant Speed Control |
Vehicle-to-vehicle Distance Control (All Speed): Vehicle-to-vehicle distance control mode (w/ full-speed range following function) Vehicle-to-vehicle Distance Control (Hi Speed): Vehicle-to-vehicle distance control mode (w/o full-speed range following function) Constant Speed Control: Constant speed mode |
- |
|
Vehicle Speed |
Vehicle speed |
Min.: 0 km/h (0 mph), Max.: 327.67 km/h (204.79 mph) |
Actual vehicle speed |
- |
|
Yaw Rate Sensor Signal |
Yaw rate value |
Min.: -100.00 deg/s, Max.: 100.00 deg/s |
Actual yaw rate value |
- |
|
Steering Angle Signal |
Steering sensor signal |
Min.: -3072.0 deg, Max.: 3070.5 deg |
Increase: Turning left Decrease: Turning right |
- |
|
Zero Point of Steering Angle Memorized in Steering Angle Sensor |
Zero point steering angle sensor |
Min.: -3072.0 deg, Max.: 3070.5 deg |
Actual zero point steering angle |
- |
|
Estimated Vehicle Acceleration |
Estimated Vehicle Acceleration |
Min.: -5.00 m/s2, Max.: 5.00 m/s2 |
Current value displayed |
- |
|
Accelerator Pedal Idle |
Accelerator pedal idle position signal |
ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
|
Forward Vehicle Distance |
Distance to preceding vehicle |
Min.: 0 m, Max.: 255 m |
Current value displayed |
- |
|
Forward Vehicle Relative Speed |
Relative speed against preceding vehicle |
-128 to 127 km/h |
Current value displayed |
- |
|
Cruise Warning Request |
Forward vehicle approach warning signal |
ON or OFF |
ON: Forward vehicle approaching OFF: Forward vehicle not approaching |
- |
|
Radar Transmitting |
Millimeter wave radar sensor assembly operation signal |
ON or OFF |
ON: Millimeter wave radar sensor assembly signal sent OFF: Millimeter wave radar sensor assembly signal stopped |
- |
|
Vehicle Information (Conv/HV) |
Vehicle Information (Conv/HV) |
Unknown, Conv or HV |
- |
- |
|
Vehicle Information (Steering Wheel Position) |
Vehicle Information (Steering Wheel Position) |
Unknown, Left or Right |
- |
- |
|
Vehicle Information (Brake Type) |
Vehicle Information (Brake Type) |
Unknown, Other, V series of Except V3H or V3H |
- |
- |
|
Accelerator Over Ride |
Accelerator pedal position signal during cruising |
ON or OFF |
ON: Accelerator over ride ON OFF: Accelerator over ride OFF |
- |
|
Front Radar Sensor High Temperature |
Millimeter wave radar sensor assembly high temperature abnormality |
Normal or High Temperature |
Normal: Millimeter wave radar sensor assembly temperature is normal High Temperature: Millimeter wave radar sensor assembly temperature is high |
- |
|
Front Radar Sensor Low Voltage |
Millimeter wave radar sensor assembly low voltage abnormality |
Normal or Low Voltage |
Normal: Millimeter wave radar sensor assembly voltage is normal Low Voltage: Millimeter wave radar sensor assembly voltage is low |
- |
|
Radar Cruise Control System Malfunction |
Dynamic radar cruise control system warning indication |
Normal or Abnormal |
Normal: Dynamic radar cruise control system warning indication (Malfunction not detected) Abnormal: Dynamic radar cruise control system warning indication (Malfunction detected) |
- |
(g) Enter the following menus: Powertrain / Engine / Data List
(h) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Neutral Position Switch |
Neutral position switch status |
ON or OFF |
ON: Shift lever in neutral OFF: Shift lever is in any position other than neutral |
- |
ACTIVE TEST
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Radar Cruise 2 / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Powertrain > Radar Cruise2 > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Radar Cruise Proximity Warning Buzzer |
- |
- |
Cannot be used |
|
Radar Cruise Stop Keeping Announce Buzzer |
- |
- |
Cannot be used |
(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(g) Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Multi Display All (White) |
Multi-information display (White display) |
ON |
- |
|
|