Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CU14 |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 09/2022] |
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): REMOVAL; 2019 - 2022 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 09/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System (for Hatchback)
|
|
-
Front door glass sub-assembly
-
Front door glass run
-
Front door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System and Audio and Visual System (for Gasoline Model))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Click here
4. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY
Click here
5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE DOOR UPPER FRAME GARNISH
Click here
9. REMOVE FRONT DOOR VENT SEAL
Click here
10. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER
Click here
11. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
13. REMOVE FRONT DOOR GLASS RUN
Click here
14. DISCONNECT FRONT DOOR WEATHERSTRIP
Click here
15. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Click here
16. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP WITH FRONT DOOR FIX WINDOW GLASS
Click here
17. REMOVE FRONT DOOR OUTSIDE STRIPE
HINT:
When removing the front door outside stripe, heat the vehicle body and front door outside stripe using a heat light.
Heating Temperature
Item
|
Temperature
|
Front Door Outside Stripe and Vehicle Body
|
40 to 60°C (104 to 140°F)
|
CAUTION:
-
Do not touch the heat light and heated parts, touching the heat light may result in burns.
-
Touching heated parts for a long time may result in burns.
*a
|
Heated Part
|
*b
|
Heat Light
|
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the front door outside stripe and vehicle body.
(b) Pull back on one of the ends of the front door outside stripe to remove it.
HINT:
When pulling on the front door outside stripe, pull it parallel to the vehicle body.
|
|
18. REMOVE NO. 2 FRONT DOOR STRIPE
HINT:
When removing the No. 2 front door stripe, heat the vehicle body and No. 2 front door stripe using a heat light.
Heating Temperature
Item
|
Temperature
|
No. 2 Front Door Stripe and Vehicle Body
|
40 to 60°C (104 to 140°F)
|
CAUTION:
-
Do not touch the heat light and heated parts, touching the heat light may result in burns.
-
Touching heated parts for a long time may result in burns.
*a
|
Heated Part
|
*b
|
Heat Light
|
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 2 front door stripe and vehicle body.
(b) Pull back on one of the ends of the No. 2 front door stripe to remove it.
HINT:
When pulling on the No. 2 front door stripe, pull it parallel to the vehicle body.
|
|
|