Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CU0H |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedures are not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane Control System
|
|
Pre-collision System
|
Lighting System (w/ AFS)(EXT)
|
Initialize back door lock
|
Power Door Lock Control System
|
|
-
Rear door glass sub-assembly
-
Rear door glass run
-
Rear door belt moulding
-
Rear door inner glass weatherstrip
|
Initialize power window control system
|
-
Auto up and down function
-
Jam protection function
-
Remote control function
-
Key-linked function
-
Wireless transmitter-linked function
-
Key-off operation function
-
Catch protection function
-
Window open warning function
|
|
NOTICE:
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
-
After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
6. REMOVE REAR SPEAKER ASSEMBLY
Click here
7. REMOVE REAR DOOR FRAME GARNISH
Click here
8. REMOVE REAR DOOR NO. 1 VENT SEAL
Click here
9. REMOVE REAR DOOR PANEL PROTECTOR
Click here
10. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
11. REMOVE REAR DOOR GLASS RUN
Click here
12. DISCONNECT REAR DOOR WEATHERSTRIP
Click here
13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
15. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP WITH REAR DOOR QUARTER WINDOW GLASS
Click here
16. REMOVE REAR DOOR BELT MOULDING
(a) Apply protective tape around the rear door belt moulding as shown in the illustration.
|
Protective Tape
|
(b) Disengage the 7 claws as shown in the illustration to remove the rear door belt moulding.
|
Remove in this Direction
|
|