Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001CNZZ |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 09/2022] |
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System): B1412; Ambient Temperature Sensor Circuit; 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022] |
DTC
|
B1412
|
Ambient Temperature Sensor Circuit
|
DESCRIPTION
The thermistor assembly is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the thermistor assembly and reads voltage changes due to changes in the resistance of the thermistor assembly.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Memory
|
B1412
|
Ambient Temperature Sensor Circuit
|
Open or short in ambient temperature sensor circuit
|
-
Thermistor assembly
-
Harness or connector
-
Air conditioning amplifier assembly
|
Memorized
(4 sec. or more)*
|
-
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
HINT:
If the ambient temperature is approximately -52.9°C (-63.22°F) or lower, DTC B1412 may be stored even though the system is normal.
WIRING DIAGRAM
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Air Conditioner > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Ambient Temp Sensor
|
Thermistor assembly
|
Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
|
Actual ambient temperature displayed
|
Thermistor assembly circuit malfunction
-
When open circuit: -23.30°C (-9.94°F)
-
When short circuit: 65.95°C (150.71°F)
|
Body Electrical > Air Conditioner > Data List
Tester Display
|
Ambient Temp Sensor
|
OK:
The display is as specified in the normal condition column.
NG
|
|
|
2.
|
INSPECT THERMISTOR ASSEMBLY
|
(a) Remove the thermistor assembly.
Click here
(b) Inspect the thermistor assembly.
Click here
OK
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
|
(a) Disconnect the I48 air conditioning amplifier assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A3-1 - I48-1 (TAM)
|
Always
|
Below 1 Ω
|
A3-2 - I48-14 (SG-2)
|
Always
|
Below 1 Ω
|
A3-1 or I48-1 (TAM) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
A3-2 or I48-14 (SG-2) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|