Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001CJJF
Model Year Start: 2019 Model: Corolla Hatchback Prod Date Range: [06/2018 - 01/2019]
Title: M20A-FKS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision system

Lighting System (w/ AFS)(EXT)

Initialize back door lock

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

Code registration (Smart Key System (for Start Function))
  • Wireless Door Lock Control System
  • Smart Key System (for Entry Function)
  • Smart Key System (for Start Function)
  • Steering lock function

2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

  • Replacement of engine assembly
  • Gas leak from exhaust system is repaired

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 09/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of continuously variable transaxle assembly
  • Input transaxle compensation code into TCM
  • Perform reset memory
  • Deceleration sensor zero point calibration
  • CVT oil pressure calibration
  • Perform road test to allow TCM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION for Initialization

2019 - 2025 MY Corolla Corolla Hatchback [06/2018 -        ]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: REGISTRATION for Registration

Replacement of ECM
  • Perform reset memory
  • CVT oil pressure calibration
  • Perform road test to allow TCM to learn

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Perform headlight ECU sub-assembly LH initialization

Lighting system (w/ AFS)(EXT)

2019 - 2021 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 06/2021]; LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model with AFS): INITIALIZATION

Front wheel alignment adjustment
  1. Perform "Reset Memory".
  2. Perform acceleration sensor zero point calibration and store system information memorization.
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System): UTILITY

CVT fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly

2019 - 2022 MY Corolla Corolla Hatchback [06/2018 - 09/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION

NOTICE:

  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; K120 / K121 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY: REMOVAL

2. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Click here 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; CLUTCH: CLUTCH UNIT (for EG60): REMOVAL

3. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
  • To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(c) Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.

4. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

(a) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(b) Using a 10 mm hexagon wrench, remove the 8 bolts and flywheel sub-assembly.

5. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(a) Remove the No. 1 crankshaft position sensor plate.

6. REMOVE REAR ENGINE OIL SEAL

(a) Using a knife, cut off the lip of the rear engine oil seal.

*a

Protective Tape

*b

Cut Position

(b) Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.

HINT:

Tape the screwdriver tip before use.