THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, Gasoline Model): OPERATION CHECK; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM100000001CDKR
Model Year Start: 2019	Model: GR Corolla	Prod Date Range: [06/2018 - 01/2019]
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, Gasoline Model): OPERATION CHECK; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]

OPERATION CHECK

CHECK CUSTOMIZE PARAMETERS

NOTICE:

The operation check below is based on the non-customized initial condition of the vehicle.

Click here

CHECK THE ENTRY UNLOCK FUNCTION

(a) Check the entry unlock function (driver door, front passenger door).

(1) Perform a wireless lock door operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.

(2) Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.

*a	0.7 to 1 m (2.30 to 3.28 ft.)

(3) With the system in unlock standby mode, grasp the front door outside handle assembly (for driver door) and check that the door unlocks.

HINT:

The system is in unlock standby mode when the electrical key transmitter sub-assembly is in the detection area and the key ID code sent by the electrical key transmitter sub-assembly matches the key ID code stored by the certification ECU (smart key ECU assembly).
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the door outside handle assembly.
Inspect the front passenger door using the same procedure.

(4) Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

NOTICE:

If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.

*a	Unlock Sensor (Backside)

HINT:

Inspect the front passenger door using the same procedure.

CHECK THE ENTRY LOCK FUNCTION

(a) Check the entry lock function (driver door, front passenger door).

NOTICE:

If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.

*a	Lock Sensor

(1) With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.

HINT:

If the door does not lock even when touching the lock sensor, touch it with your palm.
Inspect the front passenger door using the same procedure.

(2) Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly approximately 0.7 to 1 m (2.30 to 3.28 ft.) below the bottom edge of the door glass and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door locks.

HINT:

If the door does not lock even when touching the lock sensor, touch it with your palm.
As communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is carrying the electrical key transmitter sub-assembly, etc.
If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.
Inspect the front passenger door using the same procedure.
The entry lock function cannot be operated more than 3 times consecutively.

*a	0.3 m (0.984 ft.)

CHECK ENTRY BACK DOOR OPEN FUNCTION

(a) Check the entry back door open function.

(1) With the back door closed and locked, press the lock switch of the back door opener switch sub-assembly while carrying the electrical key transmitter sub-assembly and check that the back door opens.

*1	Back Door Opener Switch Sub-assembly (Open Switch)
*a	0.7 to 1 m (2.30 to 3.28 ft.)

(2) Inspect the entry back door open operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.7 to 1 m (2.30 to 3.28 ft.) from the vehicle as shown in the illustration, press the open switch of the back door opener switch sub-assembly and check that the back door opens.

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of rear bumper.

CHECK ENTRY BACK DOOR LOCK FUNCTION

(a) Check the entry back door lock function.

NOTICE:

If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box or on the floor) and a back door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.

(1) With the back door closed and unlocked, press the lock switch of the back door opener switch sub-assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the back door locks.

(2) Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and approximately 0.3 m (0.984 ft.) from the vehicle as shown in the illustration, press the lock switch of the back door opener switch sub-assembly and check that the back door locks.

*1	Back Door Opener Switch Sub-assembly (Lock Switch)
*a	0.3 m (0.984 ft.)

HINT:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the rear bumper.
If the key lock-in prevention function buzzer sounds, radio waves from the indoor electrical key antenna may be leaking from the vehicle.
The entry lock function cannot be operated more than 3 times consecutively.

CHECK PUSH-BUTTON START FUNCTION

Click here

CHECK KEY LOCK-IN PREVENTION FUNCTION (VEHICLE INTERIOR)

NOTICE:

In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.

(a) Check the key lock-in prevention function (vehicle interior).

(1) Turn the engine switch off.

(2) Place the electrical key transmitter sub-assembly on a front, rear seat or luggage room floor.

(3) Close all of the doors and make sure they are unlocked.

(4) Touch a door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.

CHECK ANSWER-BACK FUNCTION

(a) Check the answer-back function (hazard warning light flashing and buzzer sounding).

Entry Operation	Hazard Warning Light	Wireless Buzzer
Entry Lock	Flashes once	Sounds once
Entry Unlock	Flashes twice	Sounds twice

CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION

Click here

CHECK ENTRY CANCEL FUNCTION

Click here

KEY DIAGNOSTIC MODE (Using Techstream)

HINT:

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

(a) Enter the following menus: Body Electrical / Smart Key / Utility / Communication Check(Key Diag Mode).

Body Electrical > Smart Key > Utility

Tester Display
Communication Check(Key Diag Mode)

(b) Inspect the appropriate item according to the following table.

Tester Display	Inspection Item
[CH1/CH2] Overhead + Driver Side*1	Front door outside handle assembly (electrical key antenna) (for driver door)
[CH1] Overhead + Driver Side*1
[CH2] Overhead + Driver Side*1
[CH1/CH2] Overhead + Passenger Side*2	Front door outside handle assembly (electrical key antenna) (for front passenger door)
[CH1] Overhead + Passenger Side*2
[CH2] Overhead + Passenger Side*2
[CH1/CH2] Overhead + Front Room*3	No. 1 indoor electrical key antenna assembly (front floor)
[CH1] Overhead + Front Room*3
[CH2] Overhead + Front Room*3
[CH1/CH2] Overhead + Rear Room*4	No. 2 indoor electrical key antenna assembly (rear floor)
[CH1] Overhead + Rear Room*4
[CH2] Overhead + Rear Room*4
[CH1/CH2] Overhead + Back Door*5	Electrical key antenna (outside luggage compartment)
[CH1] Overhead + Back Door*5
[CH2] Overhead + Back Door*5
[CH1/CH2] Luggage + Back Door (inside)*6	No. 3 indoor electrical key antenna assembly (inside luggage compartment)
[CH1] Luggage + Back Door (inside)*6
[CH2] Luggage + Back Door (inside)*6
[CH1/CH2] Immobiliser Amp*7	Amplifier (engine switch)
[CH1] Immobiliser Amp*7
[CH2] Immobiliser Amp*7

[CH1]: Channel 1 is set.
[CH2]: Channel 2 is set.
[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.
*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.

(c) Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless buzzer sounds.

HINT:

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.

(d) *1: Front door outside handle assembly (for driver door)

*a	0.7 to 1 m (2.30 to 3.28 ft.)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.
*2: Perform the same inspection for the front passenger door (for Entry Function).

(e) *3: No. 1 indoor electrical key antenna assembly (front floor)

*a	Inspection Point

HINT:

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.

(f) *4: No. 2 indoor electrical key antenna assembly (rear floor)

*a	Inspection Point

HINT:

Place the electrical key transmitter sub-assembly on the rear seat cushion.

(g) *5: Electrical key antenna (outside luggage compartment)

*a	0.7 to 1 m (2.30 to 3.28 ft.)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.

(h) *6: No. 3 indoor electrical key antenna assembly (inside luggage compartment)

*a	Inspection Point

HINT:

Place the electrical key transmitter sub-assembly on the luggage room floor.

(i) *7: Amplifier (engine switch)

*1	Engine Switch
*2	Electrical Key Transmitter Sub-assembly

HINT:

While facing the logo side of the electrical key transmitter sub-assembly toward the engine switch, hold the transmitter near the engine switch.