Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001CBP9
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): Check Bus 5 Line for Short to +B; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]

Check Bus 5 Line for Short to +B

DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom

Trouble Area

There is no resistance between terminal 15 (CA5H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 16 (CA5L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

  • Short to +B in CAN main bus line
  • Short to +B in CAN branch line
  • Central gateway ECU (network gateway ECU)
  • Air conditioning amplifier assembly
  • Certification ECU (smart key ECU assembly)
  • Main body ECU (multiplex network body ECU)
  • Combination meter assembly
  • Meter mirror sub-assembly

    (w/ Headup Display System)

  • Headlight ECU sub-assembly RH

    (w/ AFS)

  • Headlight ECU sub-assembly LH

    (w/ AFS)

  • No. 3 CAN junction connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): DIAGNOSIS SYSTEM

  • Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Registration.

    Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the I94 No. 3 CAN junction connector.

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 3 CAN Junction Connector)

*b

to Combination Meter Assembly

*c

to Main Body ECU (Multiplex Network Body ECU)

*d

to Meter Mirror Sub-assembly

(w/ Headup Display System)

*e

to Air Conditioning Amplifier Assembly

*f

to Certification ECU (Smart Key ECU Assembly)

*g

to Central gateway ECU (Network Gateway ECU)

*h

to Headlight ECU Sub-assembly RH

(w/ AFS)

*i

to Headlight ECU Sub-assembly LH

(w/ AFS)

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

I94-1 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Combination meter assembly

I94-11 (CANL) - I26-16 (BAT)

I94-2 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Main body ECU (multiplex network body ECU)

I94-12 (CANL) - I26-16 (BAT)

I94-3 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Meter mirror sub-assembly*1

I94-13 (CANL) - I26-16 (BAT)

I94-4 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Air conditioning amplifier assembly

I94-14 (CANL) - I26-16 (BAT)

I94-5 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Certification ECU (smart key ECU assembly)

I94-15 (CANL) - I26-16 (BAT)

I94-6 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Central gateway ECU (network gateway ECU)

I94-16 (CANL) - I26-16 (BAT)

I94-7 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Headlight ECU sub-assembly RH*2

I94-17 (CANL) - I26-16 (BAT)

I94-8 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

Headlight ECU sub-assembly LH*2

I94-18 (CANL) - I26-16 (BAT)

  • *1: w/ Headup Display System
  • *2: w/ AFS

Result

Proceed to

OK

A

NG (Line to central gateway ECU (network gateway ECU))

B

NG (Line to ECU or sensor)

C

A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

C

GO TO STEP 3

B

2.

CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

(a) Disconnect the I53 central gateway ECU (network gateway ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Front view of wire harness connector

(to No. 3 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

Standard Resistance:

Tester Connection

Condition

Specified Condition

I94-6 (CANH) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

I94-16 (CANL) - I26-16 (BAT)

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.

CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)

(a) Reconnect all wire harness connectors.

(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model): TERMINALS OF ECU

(c) Measure the resistance according to the value(s) in the table below.

*1

DLC3

-

-

*a

Component with harness connected

(Central Gateway ECU (Network Gateway ECU))

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

I53-15 (CA5H) - I26-16 (BAT)

Cable disconnected from negative (-) battery terminal

6 kΩ or higher

I53-16 (CA5L) - I26-16 (BAT)

HINT:

  • If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
  • If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR