Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001C4L7
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: CLUTCH: CLUTCH PEDAL: REMOVAL; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during clutch pedal sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; PRE-COLLISION: PRE-COLLISION SYSTEM (for Gasoline Model): INITIALIZATION

Pre-collision System

Lighting System (w/ AFS)(EXT)

Initialize back door lock

Power Door Lock Control System

2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for Hatchback, Gasoline Model): INITIALIZATION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): PRECAUTION

NOTICE:

  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System)
  • After the engine switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) battery terminal. (for Navigation System)

PROCEDURE

1. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL

2. DISCONNECT CLUTCH MASTER CYLINDER ASSEMBLY

(a) Remove the clip from the clevis pin.

(b) Remove the clevis pin to disconnect the clutch master cylinder assembly from the clutch pedal sub-assembly.

3. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY

(a) Disconnect the clutch pedal stroke sensor assembly connector.

*a

Clutch Pedal Stroke Sensor Assembly Connector

*b

Clutch Switch Assembly Connector

(b) Disconnect the clutch switch assembly connector.

(c) Disengage the clamp to disconnect the wire harness from the clutch pedal support assembly.

(d) Remove the 2 bolts and No. 4 instrument panel bracket from the clutch pedal support assembly and instrument panel reinforcement assembly.

(e) Remove the 2 nuts and clutch pedal support assembly from the vehicle body.

(f) Remove the clip nut from the clutch pedal bracket sub-assembly.

4. REMOVE CLUTCH SWITCH ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; CLUTCH: CLUTCH PEDAL SWITCH: REMOVAL

5. REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; CLUTCH: CLUTCH STROKE SENSOR: REMOVAL

6. REMOVE CLUTCH PEDAL SPRING

(a) Move the clutch pedal sub-assembly to the full stroke position.

(b) Remove the clutch pedal spring from the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.

7. REMOVE CLUTCH PEDAL SUB-ASSEMBLY

(a) Mount the clutch pedal sub-assembly in a soft jaw vise.

NOTICE:

Be careful not to damage the clutch pedal sub-assembly in the vise.

(b) Remove the bolt, nut, clutch pedal sub-assembly and clutch pedal bracket sub-assembly from the clutch pedal support sub-assembly.

*1

Clutch Pedal Bracket Sub-assembly

*2

Clutch Pedal Sub-assembly

8. REMOVE CLUTCH PEDAL SPRING HOLDER

(a) Remove the clutch pedal spring holder from the clutch pedal bracket sub-assembly.

9. REMOVE CLUTCH PEDAL TURNOVER BUSHING

(a) Remove the clutch pedal turnover bushing from the clutch pedal sub-assembly.

10. REMOVE CLUTCH PEDAL SHAFT COLLAR

(a) Remove the 2 clutch pedal bushings and clutch pedal shaft collar from the clutch pedal sub-assembly.

11. REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

(a) Using SST and a hammer, remove the clutch master cylinder push rod clevis bushing from the clutch pedal sub-assembly.

SST: 09201-01055

SST: 09950-70010

09951-07100

*1

Clutch Master Cylinder Push Rod Clevis Bushing

12. REMOVE CLUTCH PEDAL PAD

(a) Remove the clutch pedal pad from the clutch pedal sub-assembly.