Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM100000001BO68
Model Year Start: 2019 Model: GR Corolla Prod Date Range: [06/2018 - 01/2019]
Title: LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model without AFS): High Beam Headlight Circuit; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]

High Beam Headlight Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the high beam headlights.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION

  • Check the operation of the low beam headlights. If the low beam headlights do not operate normally, refer to Problem Symptoms Table.

    Click here 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019]; LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model without AFS): PROBLEM SYMPTOMS TABLE

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Head Light Hi

High beam headlights

OFF or ON

-

Body Electrical > Main Body > Active Test

Tester Display

Head Light Hi

OK:

High beam headlights illuminate.

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

INSPECT NO. 1 INTEGRATION RELAY

(a) Remove the No. 1 integration relay.

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; POWER DISTRIBUTION: INTEGRATION RELAY: REMOVAL

(b) Inspect the No. 1 integration relay.

Click here 2019 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 - 01/2019]; POWER DISTRIBUTION: INTEGRATION RELAY: INSPECTION

NG

REPLACE NO. 1 INTEGRATION RELAY

OK

3.

CHECK HARNESS AND CONNECTOR (POWER SOURCE - NO. 1 INTEGRATION RELAY)

(a) Disconnect the 1B No. 1 integration relay connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

1B-9 - Body ground

Always

11 to 14 V

1B-11 - Body ground

Always

11 to 14 V
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

4.

CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the I85 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1B-12 - I85-13 (DIM)

Always

Below 1 Ω

1B-12 or I85-13 (DIM) - Body ground

Always

10 kΩ or higher
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR