Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001BNSF |
Model Year Start: 2019 |
Model: GR Corolla |
Prod Date Range: [06/2018 - 01/2019] |
Title: LIGHTING (EXT): LIGHTING SYSTEM (for Gasoline Model without AFS): Front Fog Light Circuit; 2019 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 01/2019] |
DESCRIPTION
The main body ECU (multiplex network body ECU) controls the front fog lights.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Inspect the fuses for circuits related to this system before performing the following procedure.
-
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
Click here
PROCEDURE
1.
|
CHECK OPERATION (TAILLIGHTS)
|
(a) Check the operation of the taillights.
OK:
Taillights operate normally.
OK
|
|
|
2.
|
PERFORM ACTIVE TEST USING TECHSTREAM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
Tester Display
|
Measurement Item
|
Control Range
|
Diagnostic Note
|
Front Fog Light Relay
|
Front fog lights
|
OFF or ON
|
Light control switch in tail position
|
Body Electrical > Main Body > Active Test
Tester Display
|
Front Fog Light Relay
|
OK:
Front fog light relay operates. (Front fog lights come on.)
NG
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE - FR FOG RELAY)
|
(a) Remove the FR FOG relay.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
5 (FR FOG relay) - Body ground
|
Always
|
11 to 14 V
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (FR FOG RELAY INPUT VOLTAGE)
|
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
2 (FR FOG relay) - Body ground
|
Light control switch in tail or head position
|
11 to 14 V
|
OK
|
|
|
(a) Inspect the FR FOG relay.
Click here
NG |
|
REPLACE FR FOG RELAY
|
OK
|
|
|
6.
|
CHECK HARNESS AND CONNECTOR (FR FOG RELAY - FOG LIGHT ASSEMBLY)
|
(a) Disconnect the A43 fog light assembly LH connector.
(b) Disconnect the A42 fog light assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
3 (FR FOG relay) - A43-2 (B)
|
Always
|
Below 1 Ω
|
3 (FR FOG relay) - A42-2 (B)
|
Always
|
Below 1 Ω
|
3 (FR FOG relay) or A43-2 (B) - Body ground
|
Always
|
10 kΩ or higher
|
3 (FR FOG relay) or A42-2 (B) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
7.
|
CHECK HARNESS AND CONNECTOR (FR FOG RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
|
(a) Disconnect the 4E instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
1 (FR FOG relay) - 4E-52
|
Always
|
Below 1 Ω
|
1 (FR FOG relay) or 4E-52 - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
8.
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
*a
|
Component without harness connected
(Instrument Panel Junction Block Assembly)
|
-
|
-
|
(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
4E-52 - MB-7 (FFGO)
|
Always
|
Below 1 Ω
|
9.
|
CHECK HARNESS AND CONNECTOR (FR FOG RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
|
(a) Disconnect the 4F instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
2 (FR FOG relay) - 4F-11
|
Always
|
Below 1 Ω
|
2 (FR FOG relay) or 4F-11 - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|