Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM100000001BGXP |
Model Year Start: 2019 |
Model: Corolla Hatchback |
Prod Date Range: [06/2018 - 03/2019] |
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P060747,P060787; Control Module Performance Bank 1 Watchdog/Safety MCU Failure; 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019] |
DTC
|
P060747
|
Control Module Performance Bank 1 Watchdog/Safety MCU Failure
|
DTC
|
P060787
|
Control Module Performance Bank 1 Missing Message
|
MONITOR DESCRIPTION
The ECM continuously monitors its internal ICs and the monitor IC. If the monitor IC is abnormal, the ECM illuminates the MIL and stores DTC P060747. If an internal IC is abnormal, the ECM illuminates the MIL and stores DTC P060787.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P060747
|
Control Module Performance Bank 1 Watchdog/Safety MCU Failure
|
ECM monitor IC malfunction (1 trip detection logic).
|
ECM
|
Comes on
|
DTC stored
|
SAE Code: P0607
|
P060787
|
Control Module Performance Bank 1 Missing Message
|
ECM internal IC malfunction (1 trip detection logic).
|
ECM
|
Comes on
|
DTC stored
|
SAE Code: P0607
|
MONITOR STRATEGY
Related DTCs
|
P0607: ECM/PCM processor performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
0.47 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
TYPICAL MALFUNCTION THRESHOLDS
Monitor IC software functional check
|
Fail
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the engine switch on (IG) [B].
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the Techstream off.
-
Turn the engine switch off.
-
Disconnect the Techstream.
-
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
-
Connect the cable to the negative (-) battery terminal.
-
Connect the Techstream to the DLC3.
-
Turn the engine switch on (IG).
-
Turn the Techstream on.
-
Wait 1 second or more [A].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P060747 or P060787
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
CAUTION / NOTICE / HINT
NOTICE:
After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the engine switch off.
NEXT
|
|
|
2.
|
READ OUTPUT DTC (DTC P060747 OR P060787)
|
(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) battery terminal.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Wait 1 second or more.
(g) Enter the following menus: Powertrain / Engine / Trouble Codes.
(h) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC P060747 or P060787 is output
|
B
|
|