- DTC judgment completed
- System normal
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM100000001BGX4 |
| Model Year Start: 2019 | Model: Corolla Hatchback | Prod Date Range: [06/2018 - 03/2019] |
| Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P03652A; Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range; 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019] | ||
|
DTC |
P03652A |
Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range |
DESCRIPTION
Refer to DTC P036511.
Click here
![2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: P036511; Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P03652A |
Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range |
Diagnosis condition:
Abnormal condition:
Malfunction time:
Trip logic:
Detection conditions:
Sensors/components used for detection (Main):
Sensors/components used for detection (Related):
|
|
Comes on |
DTC stored |
SAE Code: P0365 |
Reference: Inspection using an oscilloscope.
Click here
MONITOR DESCRIPTION
When the engine is cranking and no camshaft position sensor (for exhaust camshaft) signal is received for 2 times, the ECM determines that the camshaft position sensor (for exhaust camshaft) circuit is malfunctioning and illuminates the MIL and stores a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0365: Exhaust camshaft position sensor verify pulse input |
|
Required Sensors/Components (Main) |
Camshaft position sensor (for exhaust camshaft) |
|
Required Sensors/Components (Related) |
Crankshaft position sensor |
|
Frequency of Operation |
Continuous |
|
Duration |
2 times |
|
MIL Operation |
Immediate |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
|
Monitor runs whenever the following DTCs are not stored |
None |
|
Both of the following conditions are met |
- |
|
Starter |
After off to on timing |
|
Minimum battery voltage while starter on |
Less than 11 V |
TYPICAL MALFUNCTION THRESHOLDS
|
Exhaust camshaft position sensor signal |
No signal |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Start the engine [A].
- Idle the engine for 10 seconds or more [B].
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Proceed to the next screen and enter the DTC to be checked.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
-
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P036511.
Click here
CAUTION / NOTICE / HINT
HINT:
- If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.
-
DTC P03652A may be stored due to poor engine cranking. Before performing troubleshooting for this DTC, perform the check engine cranking operation procedure.
Click here
- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
CHECK TERMINAL VOLTAGE AND INTERNAL RESISTANCE (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) AND ECM) |
|
*a |
Front view of wire harness connector (to Camshaft Position Sensor (for Exhaust Camshaft)) |
HINT:
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
(a) Disconnect the camshaft position sensor (for exhaust camshaft) connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C11-3 (VC2) - Body ground |
Engine switch on (IG) |
4.5 to 5.5 V |
|
C11-1 (VVE+) - Body ground |
Engine switch on (IG) |
3.0 to 5.0 V |
(d) Turn the engine switch off.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C11-2 (VVE-) - Body ground |
Engine switch off |
Below 1 Ω |
| NG |
|
|
|
2. |
INSPECT CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) |
(a) Remove the camshaft position sensor (for exhaust camshaft).
Click here
(b) Confirm that there is no oil on the connecting parts of the camshaft position sensor (for exhaust camshaft) connector.
OK:
There is no oil on the connecting parts of the camshaft position sensor (for exhaust camshaft).
| NG |
|
|
|
3. |
INSPECT CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) |
|
*a |
Component without harness connected (Camshaft Position Sensor (for Exhaust Camshaft)) |
(a) Disconnect the camshaft position sensor (for exhaust camshaft) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (VC2) - 1 (VVE+) |
Always |
10 kΩ or higher |
|
3 (VC2) - 2 (VVE-) |
Always |
10 kΩ or higher |
|
1 (VVE+) - 2 (VVE-) |
Always |
10 kΩ or higher |
| OK |
|
REPLACE ECM
|
| NG |
|
|
4. |
CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM) |
(a) Disconnect the camshaft position sensor (for exhaust camshaft) connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C11-3 (VC2) - C76-113 (VCE1) |
Always |
Below 1 Ω |
|
C11-1 (VVE+) - C76-91 (EV1+) |
Always |
Below 1 Ω |
|
C11-2 (VVE-) - C76-114 (EV1-) |
Always |
Below 1 Ω |
|
C11-3 (VC2) or C76-113 (VCE1) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
C11-1 (VVE+) or C76-91 (EV1+) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
C11-2 (VVE-) or C76-114 (EV1-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
REPLACE ECM
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|