Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM100000001BGV9
Model Year Start: 2019 Model: Corolla Hatchback Prod Date Range: [06/2018 - 01/2019]
Title: M20A-FKS (ENGINE CONTROL): SFI SYSTEM: VEHICLE CONTROL HISTORY; 2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]

VEHICLE CONTROL HISTORY

DESCRIPTION (SFI SYSTEM)

  • Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
  • If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.
  • The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
  • The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.

    Click here 2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: DATA LIST / ACTIVE TEST

PRECAUTIONS (SFI SYSTEM)

  • As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
  • As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.

CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility

Tester Display

Vehicle Control History (RoB)

HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.

Vehicle Control History Item

Code

Item

Trigger Description

Stored Group

Reference Inspection Procedure

Link

X0800*

Engine Stall

Detection Condition (Engine Stall)

  • Prerequisite Conditions: The engine is running (after engine is judged to be difficult to start)
  • Detection Conditions: The engine speed decreases to 200 rpm or less, or stops
  • Duration: 0.5 seconds or more

08

Flowchart [Engine Stalls] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Engine Stalls

The engine stalled due to factors other than the operation of the engine switch

X0803*

Engine Stall (Compression Leakage)

It is judged that the engine is stalled due to compression leakage

08

Flow chart [Engine Stalls] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Engine Stalls

X0810

Engine Difficult to Start (Engine Starting Time Long)

Detection Condition (Engine Starting Time Long)

  • Prerequisite Conditions: STA signal is ON
  • Detection Conditions: The engine speed is less than 500 rpm for a long period of time (the starting time is long or the engine does not start)
  • Duration: Refer to Engine Difficult to Start Duration Judgment Region illustration

09

Flowchart [Engine Difficult to Start] step 3

2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Engine Difficult to Start

The engine speed decreases or the engine stalls immediately after starting

X0811*

Engine Difficult to Start (Engine Stall Immediately After Starting)

Detection Condition (Engine Stall Immediately After Starting)

  • Prerequisite Conditions: Within 2 seconds after the engine has started (engine speed is 500 rpm or more) and the engine coolant temperature is -15°C (5°F) or more
  • Detection Conditions: The engine speed decreases to 200 rpm or less (immediately after starting, the engine speed decreases or the engine stalls)
  • Duration: -

05

Flowchart [Engine Difficult to Start] step 3

2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Engine Difficult to Start

The engine speed decreases or the engine stalls immediately after starting

X0812

Engine Difficult to Start (Immobiliser)

Engine difficult to start due to immobiliser

09

Flow chart [Engine Difficult to Start] step 3

2019 MY Corolla Corolla Hatchback [06/2018 - 01/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Engine Difficult to Start

X0821*

Rough Idle #1

Detection Condition (Rough Idle)

  • Prerequisite Conditions: The engine is idling with the vehicle is stopped and the accelerator pedal is fully released
  • Detection Conditions: It is judged that combustion is unstable due to the instantaneous change in engine speed for each cylinder
  • Duration: Depending on the combustion status, between 2 and 10 seconds

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

Idling is rough due to unstable combustion in the No. 1 cylinder

X0822*

Rough Idle #2

Idling is rough due to unstable combustion in the No. 2 cylinder

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X0823*

Rough Idle #3

Idling is rough due to unstable combustion in the No. 3 cylinder

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X0824*

Rough Idle #4

Idling is rough due to unstable combustion in the No. 4 cylinder

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X082A*

Rough Idle (Plural Cylinders)

Idling is rough due to multiple cylinders

As more than one cylinder is affected, the EGR system, fuel system, etc. is suspected

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X082D*

Rough Idle (Compression Leakage)

Idling is judged to be rough due to compression leakage

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X082E*

Rough Idle (Low Frequency)

Slight rough idle symptoms are detected 3 times in 10 trips

HINT:

As the rough idle symptoms are slight, if rough idle codes other than rough idle (low frequency) code X082E are stored, this code will not be stored.

03

Flow chart [Rough Idling] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Rough Idling

X0845

Engine Lack of Power (Bad Fuel Condition)

Engine output is insufficient due to bad quality fuel

(Fuel quality is bad due to fuel aging degradation, water intrusion or fuel additive)

04

Flowchart [Lack of Power] step 3

2019 - 2020 MY Corolla Corolla Hatchback [06/2018 - 03/2019]; M20A-FKS (ENGINE CONTROL): SFI SYSTEM: Lack of Power

X0850

Engine Oil Pressure Low

The engine oil pressure is low

05

-

-

X0851

Engine Coolant Temperature High

The engine coolant temperature is high (overheating)

05

-

-

X0852

Engine RPM High

The engine speed is high (over revving)

05

-

-

X0854

Engine Coolant Temperature High (Low Voltage)

The engine coolant temperature is high (overheating) due to a low engine water pump assembly voltage causing the engine water pump assembly to stop

05

-

-

  • *: for continuously variable transaxle models
Engine Difficult to Start Duration Judgment Region (Engine Starting Time Long) (X0810)

Stored Data

Stored Group

Number of Records

Number of Freeze Frame Points

Multi Freeze Frame Data Sampling Period

Note

03*

1 code

HINT:

  • If the detection conditions for a code that is not currently stored are met, the code will be stored.
  • If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.
  • If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.
  • If rough idle codes other than Rough Idle (Low Frequency) code X082E are stored, data for code X082E will not be overwritten.

7 points (1 point at detection + 6 points before detection)

HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.

0.5 seconds

The data can be cleared by using the Techstream or by disconnecting the cable from the negative (-) battery terminal.

04

1 code

HINT:

  • If the detection conditions for a code that is not currently stored are met, the code will be stored.
  • If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.
  • If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

7 points (1 point at detection + 6 points before detection)

HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.

0.5 seconds

The data can be cleared by using the Techstream or by disconnecting the cable from the negative (-) battery terminal.

05

4 codes

HINT:

  • If the detection conditions for a code that is not currently stored are met, the code will be stored.
  • If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.
  • If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

1 point (multi freeze frame data not available)

-

  • The data can be cleared by using the Techstream.
  • The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.

08*

1 codes

HINT:

  • If the detection conditions for a code that is not currently stored are met, the code will be stored.
  • If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.
  • If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

12 points (1 point at detection + 8 points before detection + 3 points after detection)

HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.

0.5 seconds

  • The data can be cleared by using the Techstream.
  • The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.

09

1 code

HINT:

  • If the detection conditions for a code that is not currently stored are met, the code will be stored.
  • If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.
  • If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

7 points (1 point at detection + 3 points before detection + 3 points after detection)

HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.

0.5 seconds

The data can be cleared by using the Techstream or by disconnecting the cable from the negative (-) battery terminal.

  • *: for continuously variable transaxle models

HINT:

  • Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.
  • The number of available points differs depending on the stored group.
  • When the value of a data item does not change across all points, only the value at the detection point will be displayed.

HINT:

Only 1 measurement point can be displayed for stored group 05 Freeze Frame Data.

Vehicle Control History Freeze Frame Data

CLEAR VEHICLE CONTROL HISTORY (SFI SYSTEM)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (Clear).

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.

VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)

HINT:

A part of the control history can be confirmed using the vehicle control history.

Click here 2019 - 2022 MY Corolla Corolla Hatchback GR Corolla [06/2018 - 09/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made Gasoline Model): VEHICLE CONTROL HISTORY