LIGHTING (EXT): HAZARD WARNING SWITCH: REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000002GHTM
Model Year Start: 2024	Model: RAV4	Prod Date Range: [10/2023 - ]
Title: LIGHTING (EXT): HAZARD WARNING SWITCH: REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hazard warning signal switch assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedures	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed
1: When performing learning using the Techstream. Click here 2: w/o Power Back Door System
Disconnect cable from negative (-) auxiliary battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for Gasoline model)*1
		Pre-collision system
	Reset back door close position	Power back door system
	Back door lock initialization*2	Power door lock control system

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedures	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) auxiliary battery terminal	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for HV model)*
		Pre-collision system
	Reset back door close position	Power back door system
	Back door lock initialization	Power door lock control system

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE DECK BOARD ASSEMBLY (for HV Model)

Click here

3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Click here

4. REMOVE BATTERY HOLE COVER (for HV Model)

Click here

5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FKS:
Click here
for A25A-FXS:
Click here

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

6. REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

Click here

7. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Click here

8. REMOVE CONSOLE BOX ASSEMBLY

Click here

9. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Click here

10. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

11. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BRACKET

Click here

12. REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

(a) Place a hand at the rear side of the center register, detach the hazard warning signal switch assembly claw and push towards the rear of the vehicle.

HINT:

Press the hazard warning signal switch assembly from the top and bottom and detach it.

Press in this Direction

(b) Disconnect the connector.