Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000002FRAO
Model Year Start: 2024 Model: RAV4 Prod Date Range: [10/2023 -           ]
Title: AXLE AND DIFFERENTIAL: REAR AXLE CARRIER (for AWD): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

*: When performing learning using the Techstream.

Click here 2024 MY RAV4 HV [10/2023 -        ]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for HV Model): CALIBRATION

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane control system

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for HV model)*

Pre-collision system

Reset back door close position

Power back door system

2024 MY RAV4 RAV4 HV [10/2023 -        ]; DOOR / HATCH: POWER BACK DOOR SYSTEM: INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

Rear wheel alignment adjustment

  1. Perform "Reset Memory"
  2. Perform "Calibration"
  • DTCs are stored
  • ABS warning light illuminates
  • Brake system warning light (yellow indicator) illuminates
  • Slip indicator light illuminates
  • Brake control disabled or malfunctions (brake drag, etc.)

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

Suspension, tires, etc.

Television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION

Parking assist ECU initialization

Panoramic view monitor system (for HV model)

2023 - 2024 MY RAV4 HV [10/2022 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): CALIBRATION

NOTICE:

  • After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
  • When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

Rear wheel alignment adjustment

  1. Perform "Reset Memory".
  2. Perform acceleration sensor zero point calibration and store system information memorization.
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): UTILITY

Suspension, tires, etc.

Television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION

Parking assist ECU initialization

Panoramic view monitor system (for Gasoline model)

2023 - 2024 MY RAV4 [10/2022 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): CALIBRATION

HINT:

  • Use the same procedure for the RH and LH sides.
  • The following procedure is for the LH side.

PROCEDURE

1. RELEASE PARKING BRAKE

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; PARKING BRAKE: ELECTRIC PARKING BRAKE ACTUATOR: REMOVAL+

2. DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; BRAKE (REAR): REAR BRAKE: REMOVAL+

3. REMOVE REAR WHEEL

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

4. REMOVE LOWER NO. 2 CONTROL ARM COVER (w/ Cover)

Click here 2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; REAR SUSPENSION: REAR LOWER ARM: REMOVAL+

5. DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

NOTICE:

  • Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
  • Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.

(b) Remove the bolt and disconnect the skid control sensor from the rear axle carrier sub-assembly.

NOTICE:

  • Keep the tip of the skid control sensor and installation hole free of foreign matter.
  • Do not rotate or apply excessive force to the skid control sensor when removing it from the rear axle carrier sub-assembly. Rotating or applying excessive force may result in damage to the skid control sensor.

(c) Remove the nut, disengage the 2 clamps and separate the No. 2 parking brake wire assembly from the rear flexible hose bracket and rear trailing arm assembly.

6. DISCONNECT REAR FLEXIBLE HOSE

(a) Remove the bolt and disconnect the rear flexible hose from the rear flexible hose bracket.

7. REMOVE REAR AXLE SHAFT NUT

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; AXLE AND DIFFERENTIAL: REAR AXLE HUB: REMOVAL+

8. DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

(a) Remove the 2 bolts and disconnect the rear disc brake caliper assembly from the rear axle carrier sub-assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.

9. REMOVE REAR DISC

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; BRAKE (REAR): REAR BRAKE: REMOVAL+

10. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; AXLE AND DIFFERENTIAL: REAR AXLE HUB: REMOVAL+

11. REMOVE NO. 2 FLEXIBLE HOSE BRACKET

(a) Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.

12. REMOVE REAR STABILIZER LINK ASSEMBLY LH

Click here 2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; REAR SUSPENSION: REAR STABILIZER BAR: REMOVAL+

13. REMOVE REAR COIL SPRING LH

Click here 2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; REAR SUSPENSION: REAR COIL SPRING: REMOVAL+

14. REMOVE REAR LOWER COIL SPRING INSULATOR LH

Click here 2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; REAR SUSPENSION: REAR COIL SPRING: REMOVAL+

15. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

(a) Remove the bolt, nut and rear No. 1 suspension arm assembly LH from the rear axle carrier sub-assembly and rear suspension member sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

16. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

(a) Loosen the 3 bolts and nut of the rear trailing arm assembly.

(b) Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

*1

Rear Axle Carrier Pin

(c) Using a jack and wooden block, support the rear axle carrier sub-assembly.

NOTICE:

  • When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.
  • Make sure to perform this operation with the vehicle kept as low as possible.

*a

Wooden Block

*b

Jack

(d) Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

(e) Remove the 3 bolts, nut and disconnect the rear trailing arm assembly from the rear axle carrier sub-assembly.

(f) Remove the nut and disconnect the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.

(g) Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.