Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000002FR71
Model Year Start: 2024 Model: RAV4 Prod Date Range: [10/2023 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C05C000; Brake Pedal Position Sensor "A"; 2024 MY RAV4 RAV4 HV [10/2023 -        ]

DTC

C05C000

Brake Pedal Position Sensor "A"

DESCRIPTION

When the No. 2 skid control ECU (brake actuator assembly) judges that the zero point calibration of the brake pedal stroke sensor assembly is incomplete, this DTC is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Note

C05C000

Brake Pedal Position Sensor "A"

When the vehicle speed is 40km/h (25 mph) or more, a valid brake pedal stroke sensor zero point is not memorized.

  • Valid brake pedal stroke sensor assembly zero point not memorized.

    (Calibration not performed or not completed)

  • Wire harness and connector
  • Brake pedal stroke sensor assembly

Comes on

  • SAE Code: C05C0
  • Output ECU: No. 2 skid control ECU (brake actuator assembly)

HINT:

During Dealer Mode, related DTCs are cleared (except SAE code).

MONITOR DESCRIPTION

If brake pedal stroke sensor assembly zero point calibration is not performed after any of the following procedures are performed and the vehicle is driven at a certain speed or more, the No. 2 skid control ECU (brake actuator assembly) judges that learning has not been completed, the MIL is illuminated and a DTC is stored.

  • The No. 1 skid control ECU (brake booster with master cylinder assembly) has been replaced with a new one.
  • After the brake pedal stroke sensor assembly, brake pedal, brake booster with master cylinder assembly, brake actuator assembly or yaw rate and acceleration sensor (airbag ECU assembly) has been removed and installed or replaced, the zero point is cleared.

MONITOR STRATEGY

Related DTCs

C05C0: Brake pedal position sensor learning not complete

Required Sensors/Components(Main)

No. 2 skid control ECU (brake actuator assembly)

Required Sensors/Components(Related)

Speed sensor

Frequency of Operation

Continuous

Duration

-

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

*: Electronically Controlled Brake System

Monitor runs whenever the following DTCs are not stored

U0129: Lost communication with ECB*_ECU (C-bus)

Vehicle speed

40 km/h (24.85 mph) or more

TYPICAL MALFUNCTION THRESHOLDS

Either of the following conditions is met

-

Brake pedal position sensor 1: Zero position learning value

Not stored

Brake pedal position sensor 2: Zero position learning value

Not stored

COMPONENT OPERATING RANGE

Both of the following conditions are met

-

Brake pedal position sensor 1: Zero position learning value

Stored

Brake pedal position sensor 2: Zero position learning value

Stored

CONFIRMATION DRIVING PATTERN

NOTICE:

When performing the normal judgment procedure, make sure that the driver door is closed and is not opened at any time during the procedure.

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off.
  5. Turn the ignition switch to ON (READY) and turn the GTS on.
  6. Drive the vehicle at a speed of 40 km/h (25 mph) or more for 1 minute. [*]

    HINT:

    [*]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Chassis / Brake/EPB / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

Refer to DTC C110000.

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): C110000; Brake Pedal Position Sensor "A" Supply Voltage Malfunction

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration" after performing "Reset Memory".

Click here 2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

PROCEDURE

1.

PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION

(a) Perform brake pedal stroke sensor assembly zero point calibration.

Click here 2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

Chassis > Brake/EPB > Utility

Tester Display

Reset Memory

Chassis > Brake/EPB > Utility

Tester Display

Calibration

NEXT

2.

CLEAR DTC

(a) Clear the DTCs.

Chassis > Brake Booster > Clear DTCs

Chassis > Brake/EPB > Clear DTCs

(b) Turn the ignition switch off.

NEXT

3.

RECONFIRM DTC

(a) Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.

(b) Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes

Chassis > Brake/EPB > Trouble Codes

Result

Proceed to

Only DTC C05C000 is output.

A

DTCs are not output.

B

DTCs other than C05C000 are output.

C

B

END

C

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

A

4.

INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

(a) Turn the ignition switch off.

*A

except TMC Made

*B

for TMC Made

*a

Front view of wire harness connector

(to Brake Pedal Stroke Sensor Assembly)

(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(c) Disconnect the A103*1 or A110*2 brake pedal stroke sensor assembly connector.

  • *1: except TMC Made
  • *2: for TMC Made

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Turn the ignition switch to ON.

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

except TMC Made

Tester Connection

Condition

Specified Condition

A103-4 (VCSK) - A103-5 (SKG)

Ignition switch ON

4.84 to 5.16 V

for TMC Made

Tester Connection

Condition

Specified Condition

A110-4 (VCSK) - A110-5 (SKG)

Ignition switch ON

4.84 to 5.16 V

OK

REPLACE BRAKE PEDAL STROKE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR