| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002FR67 |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: BRAKE SYSTEM (OTHER): BRAKE PEDAL (w/ Vacuum Brake Booster): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake pedal support assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
*2: w/o Power Back Door System |
|||
|
Battery terminal is disconnected/reconnected |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)*1 |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization*2 |
Power door lock control system |
|
|
NOTICE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read precaution thoroughly before servicing.
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here
3. REMOVE NO. 1 AIR DUCT (for TMC Made)
Click here
4. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for TMMC Made)
Click here
5. REMOVE STOP LIGHT SWITCH ASSEMBLY
Click here
6. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER
Click here
7. DISCONNECT BRAKE PEDAL SUPPORT ASSEMBLY
|
(a) Disconnect the connector and disengage the 2 clamps. |
|
|
(b) Remove the bolt and disconnect the brake pedal support assembly from the instrument panel reinforcement assembly. |
|
8. REMOVE BRAKE PEDAL RETURN SPRING
|
(a) Remove the brake pedal return spring from the brake pedal support assembly. |
|
9. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
Click here
10. REMOVE PUSH ROD PIN
|
(a) Remove the clip and push rod pin. |
|
11. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
|
(a) w/ clip: (1) Remove the 2 clips from the brake pedal support assembly. |
|
|
(b) Remove the 4 nuts and brake pedal support assembly. |
|
12. REMOVE BRAKE PEDAL PAD
(a) Remove the brake pedal pad from the brake pedal support assembly.
|
|