Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000002FR5U
Model Year Start: 2024 Model: RAV4 Prod Date Range: [10/2023 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR (w/ Vacuum Brake Booster): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: When performing learning using the Techstream.

Click here 2024 MY RAV4 [10/2023 -        ]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for Gasoline Model): CALIBRATION

*2: w/o Power Back Door System

Battery terminal is disconnected/reconnected

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)

Stop and start system

2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: PRECAUTION

Perform steering sensor zero point calibration

Lane control system

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for Gasoline model)*1

Pre-collision system

Reset back door close position

Power back door system

2024 MY RAV4 RAV4 HV [10/2023 -        ]; DOOR / HATCH: POWER BACK DOOR SYSTEM: INITIALIZATION

Back door lock initialization*2

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

Replacement of brake actuator assembly

Operate the electric parking brake switch assembly

Parking brake indicator light blinks when the engine switch is first turned on (IG)

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM (w/ Vacuum Brake Booster): PRECAUTION

Perform system variant learning and acceleration sensor zero point calibration

  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): UTILITY

NOTICE:

  • After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
  • When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2024 MY RAV4 [10/2023 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2024 MY RAV4 RAV4 HV [10/2023 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.

4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; WIPER / WASHER: FRONT WIPER MOTOR: REMOVAL

5. REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Click here 2024 MY RAV4 HV [10/2023 -        ]; HEATING / AIR CONDITIONING: AIR CONDITIONING UNIT (for A25A-FXS): REMOVAL+

6. REMOVE BRAKE ACTUATOR WITH BRACKET

(a) Release the lock lever and disconnect the connector from the brake actuator assembly.

Release the lock lever

Disconnect the connector

NOTICE:

Be careful not to allow any brake fluid to enter the connector.

(b) Use tags or make a memo to identify the places to reconnect the brake lines.

*a

From 1st Chamber of Brake Master Cylinder Sub-assembly

*b

From 2nd Chamber of Brake Master Cylinder Sub-assembly

*c

To Front Wheel Cylinder Assembly RH

*d

To Rear Wheel Cylinder Assembly LH

*e

To Rear Wheel Cylinder Assembly RH

*f

To Front Wheel Cylinder Assembly LH

(c) Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

(d) Disengage the 5 clamps to separate the brake lines from the brake tube clamp.

NOTICE:

Do not kink or damage the brake lines.

(e) Remove the bolt and brake tube clamp.

(f) Remove the 2 bolts, nut and brake actuator with bracket.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

HINT:

Remove the brake actuator with bracket while avoiding the brake lines.

7. REMOVE BRAKE ACTUATOR ASSEMBLY

(a) Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:

  • Do not hold the brake actuator assembly by the connector.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not drop the brake actuator assembly when carrying it.

8. REMOVE BRAKE ACTUATOR BRACKET CUSHION

(a) Remove the 3 nuts and separate the brake actuator bracket assembly.

*1

No. 1 Brake Actuator Case Collar

*2

Brake Actuator Bracket Cushion

(b) Remove the 3 No. 1 brake actuator case collars from the brake actuator bracket cushion.

(c) Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.