Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000002EMA1
Model Year Start: 2024 Model: RAV4 Prod Date Range: [10/2023 -           ]
Title: STOP AND START: STOP AND START SYSTEM: P055511,P055515; Brake Booster Pressure Sensor Circuit Short to Ground; 2024 MY RAV4 [10/2023 -        ]

DTC

P055511

Brake Booster Pressure Sensor Circuit Short to Ground

DTC

P055515

Brake Booster Pressure Sensor Circuit Short to Battery or Open

DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the engine stop and start ECU judges that the signal received from the vacuum sensor assembly is abnormal, it stores DTC P055511 or P055515 and blinks the stop and start cancel indicator.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Note

P055511

Brake Booster Pressure Sensor Circuit Short to Ground

Both of the following conditions are met for 2 seconds or more (1 trip detection logic):

  • Short in vacuum sensor assembly circuit.
  • Ignition switch ON.
  • Wire harness or connector
  • Vacuum sensor assembly
  • Engine stop and start ECU

Does not come on

Blinks

SAE Code: P0557

P055515

Brake Booster Pressure Sensor Circuit Short to Battery or Open

Both of the following conditions are met for 2 seconds or more (1 trip detection logic):

  • Open or short in vacuum sensor assembly circuit.
  • Ignition switch ON.
  • Wire harness or connector
  • Vacuum sensor assembly
  • Engine stop and start ECU

Does not come on

Blinks

SAE Code: P0558

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING

HINT:

  • If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

    In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item "Status of Battery Charge Control" changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

  • If the Techstream is not available and the Data List item "Status of Battery Charge Control" cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

    If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

  • After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
  • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Stop and Start > Clear DTCs

(e) Start the engine and allow it to idle for 15 seconds or more.

(f) Stop the engine and turn the ignition switch to ON.

(g) Turn the Techstream on.

(h) Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List

Tester Display

Brake Boost Pressure

(i) While depressing the brake pedal several times, check that the Brake Boost Pressure value changes.

(j) Check that DTCs are not output.

Powertrain > Stop and Start > Trouble Codes

STOP AND START SYSTEM OPERATION CHECK

Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: OPERATION CHECK

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

  • When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: REGISTRATION

HINT:

  • Using the Techstream, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: FREEZE FRAME DATA

  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

    Click here 2024 MY RAV4 [10/2023 -        ]; STOP AND START: STOP AND START SYSTEM: DTC CHECK / CLEAR

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (PB TERMINAL VOLTAGE)

*a

Component with harness connected

(Engine Stop and Start ECU)

-

-

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A34-13 (PB) - A34-3 (BRE2)

Ignition switch ON

Higher than 0.6 V or below 4.5 V

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)

(a) Disconnect the engine stop and start ECU connector.

(b) Disconnect the vacuum sensor assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A34-13 (PB) - A95-2 (PBA)

Always

Below 1 Ω

A34-14 (BRVC) - A95-3 (VCA)

Always

Below 1 Ω

A34-3 (BRE2) - A95-1 (E2A)

Always

Below 1 Ω

A34-13 (PB) or A95-2 (PBA) - Body ground and other terminals

Always

10 kΩ or higher

A34-14 (BRVC) or A95-3 (VCA) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK ENGINE STOP AND START ECU (BRVC TERMINAL VOLTAGE)

*a

Component with harness connected

(Engine Stop and Start ECU)

-

-

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

A34-14 (BRVC) - A34-3 (BRE2)

Ignition switch ON

4.5 to 5.5 V

NG

REPLACE ENGINE STOP AND START ECU

OK

4.

REPLACE VACUUM SENSOR ASSEMBLY

(a) Replace the vacuum sensor assembly.

Click here 2019 - 2024 MY RAV4 [11/2018 -        ]; STOP AND START: VACUUM SENSOR ASSEMBLY: REMOVAL

NEXT

5.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

(e) Clear the DTC.

Powertrain > Stop and Start > Clear DTCs

NEXT

6.

CHECK DTC OUTPUT

(a) Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

(b) Check that no DTCs are output.

Powertrain > Stop and Start > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P055511 or P055515 is output

B

A

END

B

REPLACE ENGINE STOP AND START ECU