- Rear door glass sub-assembly LH
- Rear door glass sub-assembly RH
- Rear door glass run LH
- Rear door glass run RH
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002EKDA |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal and installation of auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV Model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
|
Initialize power window control system |
|
|
NOTICE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
*2: w/o Power Back Door System |
|||
|
Removal and installation of auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline Model)*1 |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization*2 |
Power door lock control system |
|
|
|
Initialize power window control system |
|
|
NOTICE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
HINT:
- Use the same procedure for the RH and LH sides.
- Use the same procedure described for the LH side.
- When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH
Click here
7. REMOVE DOOR ASSIST GRIP COVER LH
Click here
8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Click here
9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Click here
11. REMOVE REAR DOOR REAR BELT SEAL LH
Click here
12. REMOVE REAR DOOR SERVICE HOLE COVER LH
Click here
13. REMOVE REAR DOOR FRAME GARNISH LH
Click here
14. DISCONNECT REAR DOOR GLASS RUN LH
Click here
15. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
Click here
16. REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Click here
17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Click here
18. REMOVE REAR DOOR BELT MOULDING LH
(a) Apply protective tape around the rear door belt moulding LH.
|
Protective Tape |
(b) While pressing the rear door belt moulding LH, pull the edge and detach the claw as shown in the illustration.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
(c) Detach the claw to remove the rear door belt moulding LH.
|
|
Remove in this Direction |
|
|