| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000027MSR |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - ] |
| Title: PRE-COLLISION: PRE-COLLISION SYSTEM: U023A87; Lost Communication with Image Processing Module "A" Missing Message; 2023 - 2024 MY RAV4 RAV4 HV [10/2022 - ] | ||
|
DTC |
U023A87 |
Lost Communication with Image Processing Module "A" Missing Message |
DESCRIPTION
The millimeter wave radar sensor assembly is connected to the forward recognition camera via the CAN communication line. If the millimeter wave radar sensor assembly receives signals indicating that its communication with the forward recognition camera is abnormal, the millimeter wave radar sensor assembly stores DTC U023A87.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U023A87 |
Lost Communication with Image Processing Module "A" Missing Message |
When the ignition switch is ON for 3 seconds or more, a forward recognition camera communication malfunction continues for approximately 3 seconds or more. |
|
|
Pattern |
DTC output part name (Display on Techstream) |
Suspected Area (Malfunction Status) |
|||
|---|---|---|---|---|---|
|
Millimeter Wave Radar Sensor Assembly |
Forward Recognition Camera |
||||
|
Pre-Collision System |
Radar Cruise2 |
Lane Control |
Forward Recognition Camera (Front Lighting Control) |
||
|
U023A87 |
U023A87 |
U023587 |
U023587 |
||
|
○: DTC is output
-: DTC is not output |
|||||
|
Pattern 1 |
○ |
○ |
○ |
○ |
Harness or connector (Open or short) |
|
Millimeter wave radar sensor assembly (Internal malfunction) |
|||||
|
Forward recognition camera (Internal malfunction) |
|||||
|
Pattern 2 |
○ |
○ |
- |
- |
Millimeter wave radar sensor assembly (Internal malfunction) |
|
Forward recognition camera (Internal malfunction) |
|||||
HINT:
If the DTCs are output simultaneously, the inspection area can be narrowed down.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
-
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
HINT:
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click here
![2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: TARGET ADJUSTMENT(TRIANGLE TARGET)](/t3Portal/stylegraphics/info.gif)
Flat Surface Target: Click here
Driving Adjustment: Click here
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
-
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
HINT:
Forward recognition camera adjustment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Driving Adjustment: Click here
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
If there are communication malfunctions for systems other than the millimeter wave radar sensor assembly and forward recognition camera, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.
Click here
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Read each DTC and check the diagnosis pattern using the table below.
Body Electrical > Pre-Collision System > Trouble Codes
Powertrain > Radar Cruise2 > Trouble Codes
Chassis > Lane Control > Trouble Codes
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
|
Pattern |
DTC output part name (Display on Techstream / Output DTC) |
|||
|---|---|---|---|---|
|
Radar Cruise2 |
Pre-Collision System |
Lane Control |
Forward Recognition Camera (Front Lighting Control) |
|
|
Pattern 1 |
U023A87 |
U023A87 |
U023587 |
U023587 |
|
Pattern 2 |
U023A87 |
U023A87 |
- |
- |
|
Result |
Proceed to |
|---|---|
|
Pattern 1 |
A |
|
Pattern 2 |
B |
| B |
|
|
|
2. |
CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the B9 millimeter wave radar sensor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B9-5 (CA1P) - B9-6 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
B9-5 (CA1P) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
B9-6 (CA1N) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
B9-5 (CA1P) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
B9-6 (CA1N) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| OK |
|
|
|
3. |
CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the P29 forward recognition camera connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
P29-6 (CANH) - P29-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
P29-6 (CANH) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
P29-12 (CANL) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
P29-6 (CANH) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
P29-12 (CANL) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR |
|
4. |
CHECK FORWARD RECOGNITION CAMERA |
(a) Disconnect the B9 millimeter wave radar sensor assembly connector.
(b) Measure the waveform according to the table below.
Measurement Condition:
|
Tester Connection |
Condition |
Tool Setting |
Specified Condition |
|---|---|---|---|
|
B9-5 (CA1P) - B9-6 (CA1N) |
Ignition switch ON |
1 V/DIV., 100 μs./DIV. |
Waveform generation |
| OK |
|
| NG |
|
|
|