| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000026SX2 |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - ] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): C168F11; Side Camera (Left) Circuit Short to Ground; 2023 - 2024 MY RAV4 [10/2022 - ] | ||
|
DTC |
C168F11 |
Side Camera (Left) Circuit Short to Ground |
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly LH to the parking assist ECU.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
Priority |
|---|---|---|---|---|---|
|
C168F11 |
Side Camera (Left) Circuit Short to Ground |
Side camera current malfunction (Left) |
|
Circumference Monitoring Camera Control Module |
A |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here
![2023 - 2024 MY RAV4 [10/2022 - ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): CALIBRATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH) |
Pre-procedure1
(a) Disconnect the N79 parking assist ECU connector.
(b) Disconnect the J15 outer rear view mirror assembly LH connector.
Procedure1
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N79-1 (LCB+) - J15-2 (LCB+) |
Always |
Below 1 Ω |
|
N79-2 (LGND) - J15-1 (LGND) |
Always |
Below 1 Ω |
|
N79-1 (LCB+) or J15-2 (LCB+) - Body ground |
Always |
10 kΩ or higher |
|
N79-2 (LGND) or J15-1 (LGND) - Body ground |
Always |
10 kΩ or higher |
Post-procedure1
(d) None
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK PARKING ASSIST ECU (LCB+, LGND) |
Pre-procedure1
(a) Disconnect the J15 outer rear view mirror assembly LH connector.
Procedure1
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
J15-1 (LGND) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
J15-2 (LCB+) - J15-1 (LGND) |
Ignition switch ON |
7.5 to 8.5 V |
|
J15-2 (LCB+) - J15-1 (LGND) |
Ignition switch off |
Below 1 V |
Post-procedure1
(d) None
| NG |
|
|
|
3. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
|
(a) Disconnect the side television camera assembly LH connector. |
|
(b) Disconnect the outer rear view mirror assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (LCB+) - A-4 (CB+) |
Always |
Below 1 Ω |
|
1 (LGND) - A-2 (CGND) |
Always |
Below 1 Ω |
|
2 (LCB+) or A-4 (CB+) - Body ground |
Always |
10 kΩ or higher |
|
1 (LGND) or A-2 (CGND) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
|
|
4. |
REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH |
Click here
|
|
5. |
CLEAR DTC |
(a) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
|
|
6. |
CHECK FOR DTC |
(a) Check for DTCs.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
C168F11 is not output |
A |
|
C168F11 is output |
B |
| A |
|
END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE) |
| B |
|
|
|