| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000026SWZ |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - ] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): C168011; Front Camera Circuit Short to Ground; 2023 - 2024 MY RAV4 [10/2022 - ] | ||
|
DTC |
C168011 |
Front Camera Circuit Short to Ground |
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the front television camera assembly connected to the parking assist ECU.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
Priority |
|---|---|---|---|---|---|
|
C168011 |
Front Camera Circuit Short to Ground |
Open or short in the front television camera signal circuit |
|
Circumference Monitoring Camera Control Module |
A |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as panoramic view monitor system may be needed.
Click here
![2023 - 2024 MY RAV4 [10/2022 - ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for Gasoline Model): CALIBRATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY) |
Pre-procedure1
(a) Disconnect the N77 parking assist ECU connector.
(b) Disconnect the B15 front television camera assembly connector.
Procedure1
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N77-1 (BCB+) - B15-2 (BCB+) |
Always |
Below 1 Ω |
|
N77-2 (BGND) - B15-1 (BGND) |
Always |
Below 1 Ω |
|
N77-1 (BCB+) or B15-2 (BCB+) - Body ground |
Always |
10 kΩ or higher |
|
N77-2 (BGND) or B15-1 (BGND) - Body ground |
Always |
10 kΩ or higher |
Post-procedure1
(d) None
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK PARKING ASSIST ECU (BCB+, BGND) |
Pre-procedure1
(a) Disconnect the A12 front television camera assembly connector.
Procedure1
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A12-1 (BGND) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
A12-2 (BCB+) - A12-1 (BGND) |
Ignition switch ON |
7.5 to 8.5 V |
|
A12-2 (BCB+) - A12-1 (BGND) |
Ignition switch off |
Below 1 V |
Post-procedure1
(d) None
| OK |
|
| NG |
|
|
|