THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): DATA LIST / ACTIVE TEST; 2023 - 2024 MY RAV4 [10/2022

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM1000000026PS5
Model Year Start: 2023	Model: RAV4	Prod Date Range: [10/2022 - ]
Title: THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): DATA LIST / ACTIVE TEST; 2023 - 2024 MY RAV4 [10/2022 - ]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Immobiliser / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Immobiliser > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Key SW	Unlock warning switch signal	ON or OFF	ON: Door control transmitter assembly in ignition key cylinder OFF: No door control transmitter assembly in ignition key cylinder	-
IG SW	Ignition switch signal	ON or OFF	ON: Ignition switch ON OFF: Ignition switch ACC or off	"OFF" is also displayed for this item when the ignition switch is ACC.
Immobiliser	Immobiliser system status	Set or Unset	Set: No door control transmitter assembly in ignition key cylinder, or 20 seconds. elapsed after turning the ignition switch to ACC or off Unset: Door control transmitter assembly in ignition key cylinder	-
Response	Transponder chip data	NG or OK	NG: Data error OK: Data OK	-
Frame Error	Transponder chip data	NG or OK	NG: Data error OK: Data OK	-
Different Serial Number	Transponder chip data	NG or OK	NG: Data error OK: Data OK	-
Different Encrypt Code	Transponder chip data	NG or OK	NG: Data error OK: Data OK	-
Abnormal Status	Transponder chip data	NG or OK	NG: Data error OK: Data OK	-
Bcc Malfunction	Transponder chip data	NG or OK	NG: Incorrect data being sent OK: Correct data being sent	-
Sub Key	Sub key ID code signal	Reg or Unreg	Reg: Registered sub key ID code sent Unreg: Unmatching sub key ID code sent	-
Master Key	Master key ID code signal	Reg or Unreg	Reg: Registered master key ID code sent Unreg: Unmatching master key ID code sent	-
Transponder S-code	Number of registered sub keys	Min.: 0, Max.: 15	Number of registered sub keys displayed	-
Transponder M-code	Number of registered master keys	Min.: 0, Max.: 15	Number of registered master keys displayed	-
Reg Code Space Full	Key registration code memory space full	No or Yes	No: Possible to register more key codes Yes: Cannot register any more key codes	-
+B	Power source	Break or Normal	Break: Power source open Normal: Power source normal	-
Antenna Coil Status	Transponder key coil condition	Normal or Fail	Normal: Antenna coil normal Fail: Antenna coil malfunctioning	-
EEPROM Status	EEPROM status	NG or OK	NG: Data error OK: Data OK	-
E/G Start Permission	Engine start permission	NG or OK	NG: Engine start not permitted OK: Engine start permitted	-
The Number of DTCs	Number of DTCs	Min.: 0, Max.: 255	Number of stored DTCs	-

HINT:

Data from an actual vehicle provided for reference.

*1: Insert a door control transmitter assembly into the ignition key cylinder and turn the ignition switch to ACC.
*2: Turn the ignition switch to ON.
*3: Turn the ignition switch off and remove the door control transmitter assembly from the ignition key cylinder.

(f) Enter the following menus: Powertrain / Engine / Data List.

(g) Read the Data List according to the display on the Techstream.

Powertrain > Engine > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Immobiliser Fuel Cut Status

Status of immobiliser fuel cut

ON or OFF

OFF: Fuel cut off

ON: Fuel cut on

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Main Body* or Immobiliser / Active Test.

*: w/ Theft Deterrent System

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Security Indicator	Telltale light assembly (security indicator light)	OFF/ON	w/ Theft Deterrent System

Body Electrical > Immobiliser > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Security Indicator	Telltale light assembly (security indicator light)	OFF/ON	-