Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM1000000026OLL
Model Year Start: 2023 Model: RAV4 Prod Date Range: [10/2022 -           ]
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: B15FE11,B15FE13; XM Tuner Antenna Circuit Short to Ground; 2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]

DTC

B15FE11

XM Tuner Antenna Circuit Short to Ground

DTC

B15FE13

XM Tuner Antenna Circuit Open

DESCRIPTION

These DTCs are stored when a malfunction occurs in the No. 1 amplifier antenna assembly which is connected to the radio and display receiver assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

DTC Output from

Priority

B15FE11

XM Tuner Antenna Circuit Short to Ground

The XM antenna is not connected.

(2 trip detection logic)
  • No. 1 antenna amplifier assembly
  • Antenna cord sub-assembly
  • No. 3 antenna cord sub-assembly
  • No. 4 antenna cord sub-assembly
  • Radio and display receiver assembly

Navigation System

A

B15FE13

XM Tuner Antenna Circuit Open

A short occurs in the XM antenna.

(2 trip detection logic)
  • No. 1 antenna amplifier assembly
  • Antenna cord sub-assembly
  • No. 3 antenna cord sub-assembly
  • No. 4 antenna cord sub-assembly
  • Radio and display receiver assembly

Navigation System

A

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here 2023 - 2024 MY RAV4 RAV4 HV [10/2022 -        ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK CONNECTION OF ANTENNA CABLE

(a) Check if the roof antenna assembly cable is securely connected to the radio and display receiver assembly.

OK:

Roof antenna assembly cable is securely connected.

NG

SECURELY CONNECT ROOF ANTENNA ASSEMBLY
OK

2.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

NEXT

3.

CHECK FOR DTC

(a) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
A

USE SIMULATION METHOD TO CHECK

B

4.

CHECK NO. 4 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

(a) Disconnect the antenna connector from the No. 1 antenna amplifier assembly.

*a

Front view of wire harness connector

(to No. 1 Antenna Amplifier Assembly)

*b

Front view of wire harness connector

(to No. 3 Antenna Cord Sub-assembly)

(b) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A-3 - B-1

Always

Below 1 Ω

A-3a - B-1a

Always

Below 1 Ω

A-3 - Body ground

Always

10 kΩ or higher

Post-procedure1

(d) None

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

OK

5.

CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

(a) Disconnect the antenna connector from the No. 4 antenna cord sub-assembly.

*a

Front view of wire harness connector

(to No. 4 Antenna Cord Sub-assembly)

*b

Front view of wire harness connector

(to Antenna Cord Sub-assembly)

(b) Disconnect the antenna connector from the antenna cord sub-assembly.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - C-1

Always

Below 1 Ω

B-1a - C-1a

Always

Below 1 Ω

B-1 - Body ground

Always

10 kΩ or higher

Post-procedure1

(d) None

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

OK

6.

CHECK ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

(a) Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.

*a

Front view of wire harness connector

(to No. 3 Antenna Cord Sub-assembly)

*b

Front view of wire harness connector

(to Radio and Display Receiver Assembly)

(b) Disconnect the antenna connector from the radio and display receiver assembly.

Procedure1

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C-1 - D-1 (SXM)

Always

Below 1 Ω

C-1a - D-1a

Always

Below 1 Ω

C-1 - Body ground

Always

10 kΩ or higher

Post-procedure1

(d) None

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; AUDIO / VIDEO: RADIO ANTENNA CORD (for Instrument Panel): REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; AUDIO / VIDEO: RADIO ANTENNA CORD (for Instrument Panel): REMOVAL

OK

7.

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

(a) Replace the No. 1 antenna amplifier assembly with a new or known good one.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; AUDIO / VIDEO: AMPLIFIER ANTENNA: REMOVAL

NEXT

8.

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

NEXT

9.

CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Navigation System > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B
A

END (NO. 1 AMPLIFIER ANTENNA ASSEMBLY IS DEFECTIVE)
B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY