| 
                     
                        | Last Modified: 05-08-2025 | 6.11:8.1.0 | Doc ID: RM1000000026LJQ |  
                        | Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - 10/2023] |  
                        | Title: A25A-FKS (ENGINE CONTROL): ECM: REMOVAL; 2023 MY RAV4 [10/2022 - 10/2023] |  REMOVALCAUTION / NOTICE / HINTThe necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/Replaced
                     
                        
                        
                        
                        
                     
                     
                        
                           | Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |  
                           
                         
                           | Battery terminal is disconnected/reconnected | Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) | Stop and start system | 
                                 
                                    
                                       
                                          ![2023 MY RAV4 [10/2022 - 10/2023]; STOP AND START: STOP AND START SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)  |  
                           | Perform steering sensor zero point calibration | Lane control system | 
                                 
                                    
                                       
                                          ![2022 - 2025 MY RAV4 RAV4 HV [12/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  |  
                           | Parking support brake system (for Gasoline model)* |  
                           | Pre-collision system |  
                           | Reset back door close position | Power back door system (for Gasoline model) | 
                                 
                                    
                                       
                                          ![2019 - 2023 MY RAV4 [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for Gasoline Model): INITIALIZATION](/t3Portal/stylegraphics/info.gif)  |  
                           | Back door lock initialization | Power door lock control system | 
                                 
                                    
                                       
                                          ![2019 - 2025 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  |  
                           | ECM | Perform Vehicle Identification Number (VIN) or frame number registration | DTC P063051 is output | 
                                 
                                    
                                       
                                          ![2021 - 2025 MY RAV4 [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION](/t3Portal/stylegraphics/info.gif)  |  
                           | Code registration | Engine start function | w/ Smart Key System:
                                    
                                       
                                          ![2022 - 2025 MY RAV4 [12/2021 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, Gasoline Model): REGISTRATION](/t3Portal/stylegraphics/info.gif)  w/o Smart Key System:
                                    
                                       
                                          ![2023 - 2025 MY RAV4 [10/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (for Gasoline Model without Smart Key System): REGISTRATION](/t3Portal/stylegraphics/info.gif)  |  
                           | 
                                 for UB80E:
                                    
If transaxle compensation code read from ECM
                                          
                                             
Perform reset memory
Transfer transaxle compensation code
Perform road test to allow ECM to learn
 | 
                                 
                                    
Large shift shock
Deterioration of fuel efficiency
 | for Initialization:
                                    
                                       
                                          ![2019 - 2025 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  for Registration:
                                    
                                       
                                          ![2019 - 2025 MY RAV4 [11/2018 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION](/t3Portal/stylegraphics/info.gif)  |  
                           | 
                                 for UB80E:
                                    
If transaxle compensation code not read from ECM
                                          
                                             
Perform reset memory
Reset transaxle compensation code
Perform road test to allow ECM to learn
 |  
                           | 
                                 for UB80F:
                                    
If transaxle compensation code read from ECM
                                          
                                             
Perform reset memory
Transfer transaxle compensation code
Perform road test to allow ECM to learn
 | 
                                 
                                    
Large shift shock
Deterioration of fuel efficiency
 | for Initialization:
                                    
                                       
                                          ![2019 - 2025 MY RAV4 [11/2018 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)  for Registration:
                                    
                                       
                                          ![2019 - 2025 MY RAV4 [11/2018 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION](/t3Portal/stylegraphics/info.gif)  |  
                           | 
                                 for UB80F:
                                    
If transaxle compensation code not read from ECM
                                          
                                             
Perform reset memory
Reset transaxle compensation code
Perform road test to allow ECM to learn
 |  
                     NOTICE: 
                        
If the ECM has been struck or dropped, replace it.
Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here
                                 
                                    
                                       ![2021 - 2025 MY RAV4 [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION](/t3Portal/stylegraphics/info.gif) 
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
                              
                                 
                                 
                              
                              
                                 
                                    | System Name | See Procedure |  
                                    | Vehicle enrolled in Toyota Audio Multimedia system or safety connect system | 6 minutes |  
                                    | Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system | 1 minute |  PROCEDURE1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL Click here
                        
                           
                              ![2023 MY RAV4 [10/2022 - 10/2023]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL](/t3Portal/stylegraphics/info.gif)  2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY Click here
                        
                           
                              ![2023 MY RAV4 [10/2022 - 10/2023]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+](/t3Portal/stylegraphics/info.gif)  3. REMOVE INLET AIR CLEANER ASSEMBLY Click here
                        
                           
                              ![2021 - 2025 MY RAV4 [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): THROTTLE BODY: REMOVAL+](/t3Portal/stylegraphics/info.gif)  4. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE Click here
                        
                           
                              ![2021 - 2025 MY RAV4 [08/2020 -        ]; A25A-FKS (ENGINE CONTROL): THROTTLE BODY: REMOVAL+](/t3Portal/stylegraphics/info.gif)  5. REMOVE ECM 
                     
                        
                           | (a) Rotate the 3 levers while pushing the locks, and disconnect the 3 ECM connectors. NOTICE: After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors. |  |  
                     
                        
                           | (b) Remove the 2 bolts, nut and ECM. NOTICE: If the ECM has been struck or dropped, replace it. |  |  6. REMOVE NO. 1 ECM BRACKET 
                     
                        
                           | (a) Remove the 2 screws and No. 1 ECM bracket from the ECM. |  |  7. REMOVE NO. 2 ECM BRACKET 
                     
                        
                           | (a) Remove the 2 screws and No. 2 ECM bracket from the ECM. |  |  |