| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000025TO0 |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - ] |
| Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: C2198; Initialization Switch (for Test Mode DTC); 2023 - 2024 MY RAV4 RAV4 HV [10/2022 - ] | ||
|
DTC |
C2198 |
Initialization Switch (for Test Mode DTC) |
DESCRIPTION
The switch circuit inside the combination meter assembly turns on and off according to the steering pad switch assembly operation.
During test mode, the tire pressure warning light blinks at 0.125 second intervals when "Set Pressure" is selected on the multi-information display, and illuminates when the "OK" switch (steering pad switch assembly) is pressed.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Note |
|---|---|---|---|---|
|
C2198 |
Initialization Switch (for Test Mode DTC) |
Test mode procedure is performed. |
|
- |
WIRING DIAGRAM
except 12.3 inch TFT Display Type:
for 12.3 inch TFT Display Type:
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the Techstream and write them down before removal.
-
It is necessary to perform initialization
![2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ]; TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
after registration
of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.
PROCEDURE
|
1. |
INSPECT STEERING PAD SWITCH ASSEMBLY |
(a) Remove the steering pad switch assembly.
Click here
(b) Inspect the steering pad switch assembly.
Click here
| NG |
|
REPLACE STEERING PAD SWITCH ASSEMBLY
|
|
|
2. |
INSPECT SPIRAL CABLE SUB-ASSEMBLY |
(a) Remove the spiral cable sub-assembly.
Click here
(b) Inspect the spiral cable sub-assembly.
Click here
| NG |
|
REPLACE SPIRAL CABLE SUB-ASSEMBLY
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the G20 spiral cable sub-assembly connector.
(b) except 12.3 inch TFT Display Type:
Disconnect the G18 combination meter assembly connector.
(c) for 12.3 inch TFT Display Type:
Disconnect the G140 combination meter assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
except 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G20-11 (+DP) - G18-32 (MSM+) |
Always |
Below 1 Ω |
|
G20-11 (+DP) or G18-32 (MSM+) - Body ground |
Always |
10 kΩ or higher |
|
G20-10 (+DP2) - G18-15 (MSTI) |
Always |
Below 1 Ω |
|
G20-10 (+DP2) or G18-15 (MSTI) - Body ground |
Always |
10 kΩ or higher |
for 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G20-11 (+DP) - G140-29 (MSM+) |
Always |
Below 1 Ω |
|
G20-11 (+DP) or G140-29 (MSM+) - Body ground |
Always |
10 kΩ or higher |
|
G20-10 (+DP2) - G140-12 (MSTI) |
Always |
Below 1 Ω |
|
G20-10 (+DP2) or G140-12 (MSTI) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE WARNING ECU AND RECEIVER) |
(a) Disconnect the M60 tire pressure warning ECU and receiver connector.
(b) except 12.3 inch TFT Display Type:
Disconnect the G18 and G19 combination meter assembly connectors.
(c) for 12.3 inch TFT Display Type:
Disconnect the G141 combination meter assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
except 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M60-3 (CLSW) - G19-24 (INT) |
Always |
Below 1 Ω |
|
M60-3 (CLSW) or G19-24 (INT) - Body ground |
Always |
10 kΩ or higher |
|
G18-23 (ES) - Body ground |
Always |
Below 1 Ω |
for 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M60-3 (CLSW) - G141-34 (INT) |
Always |
Below 1 Ω |
|
M60-3 (CLSW) or G141-34 (INT) - Body ground |
Always |
10 kΩ or higher |
|
G141-2 (ES) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
CHECK TERMINAL VOLTAGE (INT) |
(a) Connect the M60 tire pressure warning ECU and receiver connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
except 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G19-24 (INT) - Body ground |
Ignition switch ON |
8 to 15 V |
|
*A |
except 12.3 inch TFT Display Type: |
|
*a |
Front view of wire harness connector (to Combination Meter Assembly) |
Standard Voltage:
for 12.3 inch TFT Display Type:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G141-34 (INT) - Body ground |
Ignition switch ON |
8 to 15 V |
|
*B |
for 12.3 inch TFT Display Type: |
|
*a |
Front view of wire harness connector (to Combination Meter Assembly) |
| OK |
|
| NG |
|
|
|