- Perform reset memory
- Input transaxle compensation code into ECM
- Perform road test to allow ECM to learn
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002591I |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - 10/2023] |
| Title: GF1A (TRANSFER / 4WD / AWD): TRANSFER ASSEMBLY: REMOVAL; 2023 MY RAV4 [10/2022 - 10/2023] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the transfer assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replacement Part or Procedure |
Necessary Procedure |
Effect/Inoperative when not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Automatic transaxle assembly |
|
|
for Initialization:
for Registration:
|
|
Automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
|
|
Front wheel alignment adjustment |
|
|
|
|
Suspension, tires, etc. |
Television camera assembly optical axis (Back camera position setting) |
Parking assist monitor system |
|
|
Parking assist ECU initialization |
Panoramic view monitor system (for Gasoline model) |
|
|
|
Panoramic view monitor system (for HV model) |
|
||
NOTICE:
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
|
System Name |
See Procedure |
|---|---|
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system |
6 minutes |
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system |
1 minute |
CAUTION:
-
The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.
*a
An Object Exceeding Weight Limit of Engine Lifter
-
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
-
The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.
*a
An Object Exceeding Weight Limit of Transmission Jack
PROCEDURE
1. REMOVE TRANSAXLE ASSEMBLY
Click here
![2023 MY RAV4 [10/2022 - 10/2023]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE ASSEMBLY: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE PROPELLER SHAFT HEAT INSULATOR
Click here
3. REMOVE NO. 1 PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
|
(a) Remove the 2 bolts and No. 1 propeller shaft heat insulator bracket sub-assembly. |
|
4. REMOVE REAR ENGINE MOUNTING INSULATOR
Click here
5. REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY
Click here
6. REMOVE TRANSFER ASSEMBLY
|
(a) for Type A: Remove the 6 nuts, 2 bolts and transfer from the transaxle. |
|
|
(b) for Type B: Remove the 8 nuts and transfer assembly from the transaxle. |
|
7. REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT
Click here
|
|