- Perform "Reset Memory".
- Perform acceleration sensor zero point calibration and store system information memorization.
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000224GM |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: ALIGNMENT / HANDLING DIAGNOSIS: REAR WHEEL ALIGNMENT: ADJUSTMENT; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ] | ||
ADJUSTMENT
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below.
Necessary Procedures After Adjustment
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Rear wheel alignment adjustment |
w/ Vacuum brake booster |
|
|
|
w/o Vacuum brake booster
|
|
|
CAUTION / NOTICE / HINT
Standard (Unloaded Vehicle)
|
Destination |
North America |
Mexico |
|||||
|
Tire Size |
225/65R17 |
225/60R18 |
235/55R19 |
225/65R17 |
225/60R18 |
235/55R19 |
|
|
Camber |
-1°00' (-1.00°) |
-1°00' (-1.00°) |
-1°00' (-1.00°) |
-1°05' (-1.08°) |
-1°05' (-1.08°) |
-1°05' (-1.08°) |
|
|
Toe-in |
mm |
0.3 mm (0.012 in.) |
0.3 mm (0.012 in.) |
0.3 mm (0.012 in.) |
2.6 mm (0.102 in.) |
2.6 mm (0.102 in.) |
2.7 mm (0.106 in.) |
|
deg |
0°02' (0.03°) |
0°02' (0.03°) |
0°02' (0.03°) |
0°14' (0.23°) |
0°13' (0.22°) |
0°14' (0.23°) |
|
Tolerance
|
Camber |
+/- 45' (0.75°) |
|
|
Toe-in |
mm |
+/- 2 mm (0.079 in.) |
|
deg |
+/- 10' (0.17°) |
|
Left-right Difference
|
Camber |
45' (0.75°) or less |
PROCEDURE
1. INSPECT TIRES
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; TIRE / WHEEL: TIRE AND WHEEL SYSTEM: INSPECTION](/t3Portal/stylegraphics/info.gif)
2. MEASURE VEHICLE HEIGHT
Click here
3. INSPECT CAMBER
NOTICE:
Inspect while the vehicle is unloaded.
|
(a) Install a camber-caster-kingpin gauge. |
|
(b) Inspect the camber.
Check the values in the top table.
Click here
HINT:
Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.
4. INSPECT TOE-IN
NOTICE:
Inspect while the vehicle is unloaded.
(a) Bounce the vehicle up and down at the corners to stabilize the suspension.
(b) Release the parking brake and move the shift lever to N (for Automatic transaxle, Hybrid transaxle).
(c) Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)
(d) Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).
|
*a |
Tread Center Mark |
|
*b |
Dimension B |
|
Front of the Vehicle |
(e) Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.
HINT:
Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.
(f) Measure the distance between the tread center marks on the front of the rear wheels (dimension A).
Check the values in the top table.
Click here
|
*a |
Dimension A |
|
|
Front of the Vehicle |
HINT:
Measure "B - A" only when "C + D" cannot be measured.
If the toe-in is not within the specified range, adjust it at the rear suspension toe adjust cam sub-assembly.
5. ADJUST TOE-IN
|
(a) Loosen the nut of the rear No. 2 suspension arm assembly (on the rear suspension member sub-assembly side). NOTICE: Hold the rear suspension toe adjust cam sub-assembly while rotating the nut. |
|
(b) Rotate the rear suspension toe adjust cam sub-assembly to adjust the toe-in.
Check the values in the top table.
Click here
HINT:
- Rotating the rear suspension toe adjust cam sub-assembly by one notch changes the toe by approximately 2.8 mm (0.112 in.).
- Perform adjustments so that the value is as close as possible to the median of the specified range.
|
|
Front of the Vehicle |
(c) Tighten the nut of the rear No. 2 suspension arm assembly (on the rear suspension member sub-assembly side).
Torque:
103 N·m {1050 kgf·cm, 76 ft·lbf}
NOTICE:
Hold the rear suspension toe adjust cam sub-assembly while rotating the nut.
6. ELECTRONICALLY CONTROLLED BRAKE SYSTEM CALIBRATION
HV model:
Gasoline model:
|
|