| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000224DK |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: A25A-FKS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: INSTALLATION; 2022 - 2024 MY RAV4 [12/2021 - ] | ||
INSTALLATION
CAUTION / NOTICE / HINT
NOTICE:
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. INSTALL CYLINDER HEAD GASKET
(a) Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.
(b) Place a new cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.
|
*a |
Lot No. |
|
Front of Engine |
NOTICE:
Make sure that the cylinder head gasket is installed in the correct orientation.
2. INSTALL CYLINDER HEAD SUB-ASSEMBLY
Click here
3. INSTALL NO. 2 CAMSHAFT
Click here
4. INSTALL CAMSHAFT
Click here
5. INSTALL CAMSHAFT BEARING CAP
Click here
6. INSTALL VALVE STEM CAP
Click here
7. INSTALL VALVE LASH ADJUSTER ASSEMBLY
Click here
8. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Click here
9. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY
Click here
10. INSTALL FUEL PUMP LIFTER GUIDE
Click here
11. INSTALL TIMING CHAIN COVER ASSEMBLY
Click here
12. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Click here
13. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Click here
14. INSTALL NO. 1 CHAIN VIBRATION DAMPER
Click here
15. INSTALL CHAIN TENSIONER SLIPPER
Click here
16. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Click here
17. INSTALL CHAIN SUB-ASSEMBLY
Click here
18. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Click here
19. INSTALL OIL PUMP DRIVE CHAIN SUB-ASSEMBLY
Click here
20. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
Click here
21. INSTALL NO. 2 TIMING CHAIN COVER ASSEMBLY
Click here
22. INSTALL TIMING CHAIN COVER OIL SEAL
Click here
23. INSTALL SPARK PLUG TUBE GASKET
Click here
24. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Click here
25. INSTALL OUTLET WATER BY-PASS SUB-ASSEMBLY
Click here
26. INSTALL WATER OUTLET
Click here
27. INSTALL CRANKSHAFT PULLEY ASSEMBLY
Click here
28. INSTALL VACUUM PUMP ASSEMBLY
Click here
29. CONNECT NO. 2 WATER BY-PASS HOSE (w/ Oil Cooler)
(a) Connect the No. 2 water by-pass hose to the water by-pass pipe sub-assembly and slide the clip to secure it.
30. CONNECT NO. 1 WATER BY-PASS HOSE (w/ Oil Cooler)
(a) Connect the No. 1 water by-pass hose to the cylinder block sub-assembly and slide the clip to secure it.
31. INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY
Click here
32. INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
Click here
33. INSTALL OIL PRESSURE CONTROL VALVE ASSEMBLY
Click here
34. INSTALL PURGE VALVE (PURGE VSV)
Click here
35. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Click here
36. INSTALL IGNITION COIL ASSEMBLY
Click here
37. INSTALL FUEL INJECTOR SEAL
Click here
38. INSTALL DIRECT FUEL INJECTOR ASSEMBLY
Click here
39. INSTALL FUEL DELIVERY PIPE
Click here
40. INSTALL PORT FUEL INJECTOR ASSEMBLY
Click here
41. INSTALL NO. 5 ENGINE WIRE
Click here
42. INSTALL INJECTOR VIBRATION INSULATOR
Click here
43. INSTALL NO. 1 DELIVERY PIPE SPACER
Click here
44. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
Click here
45. INSTALL NO. 7 WATER BY-PASS HOSE
Click here
46. TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
Click here
47. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
Click here
48. INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
Click here
49. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
Click here
50. CONNECT FUEL TUBE SUB-ASSEMBLY
Click here
51. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
Click here
52. INSTALL INTAKE MANIFOLD
Click here
53. INSTALL NO. 2 WATER BY-PASS PIPE
Click here
54. INSTALL NO. 3 WATER BY-PASS PIPE
Click here
55. SET EGR VALVE ASSEMBLY
Click here
56. INSTALL NO. 4 WATER BY-PASS HOSE
Click here
57. INSTALL EGR COOLER ASSEMBLY
Click here
58. INSTALL EGR VALVE ASSEMBLY
Click here
59. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
Click here
60. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
Click here
61. INSTALL EXHAUST MANIFOLD
Click here
62. INSTALL MANIFOLD STAY
Click here
63. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Click here
64. INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Click here
65. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Click here
66. INSTALL NO. 3 TIMING CHAIN COVER
Click here
67. INSTALL TIMING GEAR COVER INSULATOR
Click here
68. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Click here
69. INSTALL NO. 2 ENGINE COVER
Click here
70. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY
Click here
71. INSTALL GENERATOR ASSEMBLY
-
for 100 A, 130 A Type:
Click here
-
for 150 A Type:
Click here
-
for VALEO Made:
Click here
72. INSTALL V-RIBBED BELT
Click here
73. INSTALL ENGINE HANGERS
Click here
74. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Click here
|
|