A25A-FXS (ENGINE MECHANICAL): ENGINE UNIT: INSTALLATION; 2022 - 2024 MY RAV4 HV [12/2021

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM1000000021JWC
Model Year Start: 2022	Model: RAV4 HV	Prod Date Range: [12/2021 - ]
Title: A25A-FXS (ENGINE MECHANICAL): ENGINE UNIT: INSTALLATION; 2022 - 2024 MY RAV4 HV [12/2021 - ]

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

PROCEDURE

1. INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

(a) Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.

Torque:

16 N·m {163 kgf·cm, 12 ft·lbf}

2. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

(a) Apply a light coat of engine oil to a new O-ring.

(b) Install the O-ring to the engine oil level dipstick guide.

(c) Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(d) Install the engine oil level dipstick.

3. INSTALL IGNITION COIL ASSEMBLY

Click here

4. INSTALL FUEL INJECTOR SEAL

Click here

5. INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Click here

6. INSTALL FUEL DELIVERY PIPE

Click here

7. INSTALL PORT FUEL INJECTOR ASSEMBLY

Click here

8. INSTALL NO. 5 ENGINE WIRE

Click here

9. INSTALL INJECTOR VIBRATION INSULATOR

Click here

10. INSTALL NO. 1 DELIVERY PIPE SPACER

Click here

11. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here

12. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

13. INSTALL NO. 6 ENGINE WIRE

(a) Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Attach the 2 clamps.

14. INSTALL SENSOR WIRE

(a) Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Attach the 3 clamps.

15. INSTALL NO. 7 WATER BY-PASS HOSE

(a) Install the No. 7 water by-pass hose and slide the 2 clips to secure them.

16. TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Click here

17. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Click here

18. INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Click here

19. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

(a) Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:

Specified tightening torque :

35 N·m {357 kgf·cm, 26 ft·lbf}

NOTICE:

Do not adjust the torque in the loosening direction.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

*a	17 mm Union Nut Wrench
*b	Torque Wrench Fulcrum Length
	Union Nut
	Bolt

(b) Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:

Specified tightening torque :

35 N·m {357 kgf·cm, 26 ft·lbf}

NOTICE:

Do not adjust the torque in the loosening direction.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

20. CONNECT FUEL TUBE SUB-ASSEMBLY

Click here

21. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Click here

22. INSTALL INTAKE MANIFOLD

Click here

23. INSTALL NO. 2 WATER BY-PASS PIPE

(a) Install the bolt (A).

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(b) Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

24. INSTALL NO. 3 WATER BY-PASS PIPE

(a) Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.

(b) Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

25. SET EGR VALVE ASSEMBLY

(a) Set the EGR valve assembly to the camshaft housing.

HINT:

At this time, do not install the parts with bolts.

26. INSTALL NO. 4 WATER BY-PASS HOSE

(a) Connect the No. 4 water by-pass hose to the EGR valve assembly and slide the clip to secure it.

27. INSTALL EGR COOLER ASSEMBLY

(a) Install a new EGR cooler gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side.

Claw

(b) Install a new EGR valve gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR cooler assembly side.

(1) Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 2 bolts and 3 nuts.

	Bolt
	Nut

(2) Tighten the 2 bolts and 3 nuts in the order shown in the illustration.

Torque:

24 N·m {245 kgf·cm, 18 ft·lbf}

(d) Type B:

	Bolt
	Nut

(1) Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 3 bolts and 2 nuts.

(2) Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:

24 N·m {245 kgf·cm, 18 ft·lbf}

(e) Connect the No. 3 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.

(f) Connect the No. 4 water by-pass hose to the EGR cooler assembly and slide the clip to secure it.

28. INSTALL EGR VALVE ASSEMBLY

(a) Using an 8 mm socket wrench, install the EGR valve assembly to the camshaft housing sub-assembly with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Connect the No. 8 water by-pass hose to the EGR valve assembly and slide the clip to secure it.

29. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Click here

30. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Click here

31. INSTALL EXHAUST MANIFOLD

Click here

32. INSTALL MANIFOLD STAY

Click here

33. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

(a) for Type A:

(1) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) for Type B:

(1) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

34. INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

(a) Install the water hose clamp bracket with the 2 bolts as shown in the illustration.

Torque:

13 N·m {133 kgf·cm, 10 ft·lbf}

NOTICE:

Temporarily install the bolt (A), and then tighten the 2 bolts in the order of (B) and (A).

(b) Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.
Make sure that the claws of the clip are within the location shown in the illustration.

*a	Paint Mark
*b	90° (Claw of Clip Location)

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

35. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

(a) Connect the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

(b) Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.

36. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

(a) Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with pulley with the 2 stud bolts.

Torque:

5.0 N·m {51 kgf·cm, 44 in·lbf}

(b) Install the compressor assembly with pulley with the bolt and 2 nuts.

	Bolt
	Nut

Torque:

24.5 N·m {250 kgf·cm, 18 ft·lbf}

HINT:

Tighten the bolt and nuts in the order shown in the illustration.

37. INSTALL DRIVE SHAFT BEARING BRACKET

(a) Install the drive shaft bearing bracket with the 3 bolts.

Torque:

63.7 N·m {650 kgf·cm, 47 ft·lbf}