Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM1000000021JW8
Model Year Start: 2022 Model: RAV4 HV Prod Date Range: [12/2021 - 10/2022]
Title: A25A-FXS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2022 MY RAV4 HV [12/2021 - 10/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2019 - 2022 MY RAV4 HV [02/2019 - 10/2022]; PARK ASSIST / MONITORING: PARKING SUPPORT BRAKE SYSTEM (for HV Model): CALIBRATION

Auxiliary battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane control system

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Parking support brake system (for HV model)*

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system (for HV model)

2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): INITIALIZATION

Reset back door close position

Power back door system (for HV model)

2019 - 2023 MY RAV4 HV [11/2018 - 10/2023]; DOOR / HATCH: POWER BACK DOOR SYSTEM (for HV Model): INITIALIZATION

Back door lock initialization

Power door lock control system

2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM: INITIALIZATION

Replacement of ECM

Perform Vehicle Identification Number (VIN) registration

DTC P063051 is output

2021 - 2024 MY RAV4 RAV4 HV [08/2020 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

Grille shutter switch specification infomation

Vehicle control history (RoB) [X260E] is stored

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

  • Gas leak from exhaust system is repaired
  • Replacement of air fuel ratio sensor

Inspection after repair

  • Poor idle, etc.
  • Engine start function, etc.

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; A25A-FXS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of inverter with converter assembly

Resolver learning

  • DTCs are stored
  • Slight vibration at a vehicle speed of 5 km/h (3 mph) or less
  • Shock or vibration during acceleration

2019 - 2024 MY RAV4 HV [02/2019 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for AWD with NICKEL METAL HYDRIDE BATTERY): UTILITY

Replacement of hybrid vehicle transaxle assembly

  • Resolver learning
  • Initialize resolver

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2019 - 2022 MY RAV4 RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION

  • Parking assist ECU initialization
  • Adjust steering angle

Panoramic view monitor system (for HV model)

2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): CALIBRATION

Front wheel alignment adjustment

  1. Perform "Reset Memory"
  2. Perform "Calibration"
  • DTCs are stored
  • ABS warning light illuminates
  • Brake system warning light (yellow indicator) illuminates
  • Slip indicator light illuminates
  • Brake control disabled or malfunctions (brake drag, etc.)

2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/o Vacuum Brake Booster): UTILITY

Front bumper assembly (Including removal and installation)

Front television camera view adjustment

Panoramic view monitor system (for HV model)

2019 - 2022 MY RAV4 HV [11/2018 - 10/2022]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): CALIBRATION

NOTICE:

  • After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) auxiliary battery terminal.

    Waiting Time before Disconnecting Cable from Negative (-) Auxiliary Battery Terminal

    System Name

    See Procedure

    Vehicle enrolled in Toyota Audio Multimedia system or safety connect system

    6 minutes

    Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system

    1 minute

  • This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; P710 (HYBRID TRANSMISSION / TRANSAXLE): HYBRID VEHICLE TRANSAXLE: REMOVAL

2. REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(c) Remove the 6 bolts and transmission input damper assembly from the flywheel sub-assembly.

3. REMOVE FLYWHEEL SUB-ASSEMBLY

(a) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(b) Remove the 8 bolts and flywheel sub-assembly from the crankshaft.

4. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(a) Remove the No. 1 crankshaft position sensor plate.

5. REMOVE REAR ENGINE OIL SEAL

(a) Using a knife, cut off the lip of the rear engine oil seal.

*a

Protective Tape

*b

Cut Position

(b) Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.

HINT:

Tape the screwdriver tip before use.