Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM1000000021JQM
Model Year Start: 2022 Model: RAV4 Prod Date Range: [12/2021 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): C14E614,C14E914; Left Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]

DTC

C14E614

Left Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open

DTC

C14E914

Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC C050C12

Click here 2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): C050C12,C051212; Left Rear Wheel Speed Sensor Circuit Short to Battery

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C14E614

Left Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open

An open or short in the speed sensor power supply circuit is detected for 0.12 seconds or more.
  • Rear speed sensor LH (rear axle hub and bearing assembly LH)*1
  • Rear speed sensor LH*2
  • Wire harness or connector
  • Skid control sensor wire LH (No. 2 parking brake wire assembly)
  • Skid control ECU (brake actuator assembly)

C14E914

Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open

An open or short in the speed sensor power supply circuit is detected for 0.12 seconds or more.
  • Rear speed sensor RH (rear axle hub and bearing assembly RH)*1
  • Rear speed sensor RH*2
  • Wire harness or connector
  • Skid control sensor wire RH (No. 1 parking brake wire assembly)
  • Skid control ECU (brake actuator assembly)

*1: for 2WD

*2: for AWD

DTC Detection Conditions: C14E614

 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

An open in the speed sensor power supply circuit is detected.

○

-

A short in the speed sensor power supply circuit is detected.

-

○

Detection Time

0.12 seconds or more.

0.12 seconds or more.

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

DTC Detection Conditions: C14E914

 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

An open in the speed sensor power supply circuit is detected.

○

-

A short in the speed sensor power supply circuit is detected.

-

○

Detection Time

0.12 seconds or more.

0.12 seconds or more.

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

Refer to DTC C050C12.

Click here 2022 - 2024 MY RAV4 RAV4 HV [12/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): C050C12,C051212; Left Rear Wheel Speed Sensor Circuit Short to Battery

CAUTION / NOTICE / HINT

NOTICE:

  • After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): UTILITY

  • After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (w/ Vacuum Brake Booster): TEST MODE PROCEDURE

PROCEDURE

1.

CHECK VEHICLE

(a) Check the vehicle specification.

Result

Proceed to

for 2WD

A

for AWD

B
B

GO TO STEP 5

A

2.

CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*A

for LH

*B

for RH

*a

Front view of skid control sensor wire (parking brake wire assembly)

(to Rear Speed Sensor (Rear Axle Hub and Bearing Assembly))

(b) Disconnect the M50 or N58 rear speed sensor (rear axle hub and bearing assembly) connector.

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for LH

Tester Connection

Condition

Specified Condition

N58-2 (LA+) - N58-1 (LA-)

Ignition switch ON

11 to 14 V

for RH

Tester Connection

Condition

Specified Condition

M50-2 (RA+) - M50-1 (RA-)

Ignition switch ON

11 to 14 V
OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; AXLE AND DIFFERENTIAL: REAR AXLE HUB: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; AXLE AND DIFFERENTIAL: REAR AXLE HUB: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; AXLE AND DIFFERENTIAL: REAR AXLE HUB: REMOVAL

NG

3.

CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*A

for LH

*B

for RH

*a

Front view of wire harness connector

(to Skid Control Sensor Wire (Parking Brake Wire Assembly))

(b) Disconnect the MM4 or NN12 skid control sensor wire (parking brake wire assembly) connector.

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for LH

Tester Connection

Condition

Specified Condition

NN12-3 - NN12-4

Ignition switch ON

11 to 14 V

for RH

Tester Connection

Condition

Specified Condition

MM4-3 - MM4-4

Ignition switch ON

11 to 14 V
OK

REPLACE PARKING BRAKE WIRE ASSEMBLY
NG

4.

CHECK HARNESS AND CONNECTOR (PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(b) Disconnect the A39 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the MM4 or NN12 skid control sensor wire (parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LH

Tester Connection

Condition

Specified Condition

NN12-3 or A39-39 (RL+) - Body ground

Always

10 kΩ or higher

for RH

Tester Connection

Condition

Specified Condition

MM4-3 or A39-22 (RR+) - Body ground

Always

10 kΩ or higher
OK

REPLACE BRAKE ACTUATOR ASSEMBLY 2021 - 2022 MY RAV4 RAV4 HV [08/2020 - 10/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR (w/ Vacuum Brake Booster): REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR (w/ Vacuum Brake Booster): REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR (w/ Vacuum Brake Booster): REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.

CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*A

for LH

*B

for RH

*a

Front view of skid control sensor wire (parking brake wire assembly)

(to Rear Speed Sensor)

(b) Disconnect the M50 or N58 rear speed sensor connector.

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for LH

Tester Connection

Condition

Specified Condition

N58-2 (LA+) - N58-1 (LA-)

Ignition switch ON

11 to 14 V

for RH

Tester Connection

Condition

Specified Condition

M50-2 (RA+) - M50-1 (RA-)

Ignition switch ON

11 to 14 V
OK

REPLACE REAR SPEED SENSOR

NG

GO TO STEP 3