Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM1000000021ISH
Model Year Start: 2022 Model: RAV4 HV Prod Date Range: [12/2021 -           ]
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): Open in Bus 2 Main Bus Line; 2022 - 2024 MY RAV4 HV [12/2021 -        ]

Open in Bus 2 Main Bus Line

DESCRIPTION

There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom

Trouble Area

Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

  • Open in CAN main bus wire
  • Central gateway ECU (network gateway ECU)
  • ECM
  • No. 3 CAN junction connector

This malfunction is not related to the lines of a CAN branch or to ECUs or sensors connected to a CAN branch.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2019 - 2024 MY RAV4 HV [02/2019 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): DIAGNOSIS SYSTEM 2023 MY RAV4 HV [10/2022 - 10/2023]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): DIAGNOSIS SYSTEM 2024 MY RAV4 HV [10/2023 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): DIAGNOSIS SYSTEM

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.

(b) Disconnect the No. 3 CAN junction connector.

*a

Front view of wire harness connector

(to No. 3 CAN Junction Connector)

*b

to Central Gateway ECU (Network Gateway ECU)

*c

to ECM

-

-

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Connected to

G103-1 (CANH) - G103-11 (CANL)

Cable disconnected from negative (-) auxiliary battery terminal

108 to 132 Ω

Central gateway ECU (network gateway ECU)

G103-3 (CANH) - G103-13 (CANL)

Cable disconnected from negative (-) auxiliary battery terminal

108 to 132 Ω

ECM

Result

Proceed to

OK

A

NG (Central gateway ECU [network gateway ECU] CAN main wire)

B

NG (ECM CAN main wire)

C

A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

C

GO TO STEP 3

B

2.

CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

(a) Reconnect the G103 No. 3 CAN junction connector.

(b) Disconnect the central gateway ECU (network gateway ECU) connector.

*a

Front view of wire harness connector

(to Central Gateway ECU [Network Gateway ECU])

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

G72-18 (CA4H) - G72-17 (CA4L)

Cable disconnected from negative (-) auxiliary battery terminal

108 to 132 Ω

OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; NETWORKING: NETWORK GATEWAY ECU: REMOVAL 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]; NETWORKING: NETWORK GATEWAY ECU: REMOVAL 2024 MY RAV4 RAV4 HV [10/2023 -        ]; NETWORKING: NETWORK GATEWAY ECU: REMOVAL

NG

REPAIR OR REPLACE CAN MAIN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 3 CAN JUNCTION CONNECTOR)

3.

CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 3 CAN JUNCTION CONNECTOR)

(a) Reconnect the G103 No. 3 CAN junction connector.

(b) Disconnect the ECM connector.

*a

Front view of wire harness connector

(to ECM)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A24-8 (CANH) - A24-18 (CANL)

Cable disconnected from negative (-) auxiliary battery terminal

108 to 132 Ω

OK

REPLACE ECM 2022 MY RAV4 HV [12/2021 - 10/2022]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; A25A-FXS (ENGINE CONTROL): ECM: REMOVAL

NG

REPAIR OR REPLACE CAN MAIN BUS WIRE OR CONNECTOR (ECM - NO. 3 CAN JUNCTION CONNECTOR)