| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000021GX0 |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - 10/2022] |
| Title: CRUISE CONTROL: LANE CONTROL SYSTEM: U023587; Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022] | ||
|
DTC |
U023587 |
Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message |
DESCRIPTION
The forward recognition camera and millimeter wave radar sensor assembly communicate via CAN communication. If there is an error in the communication with the millimeter wave radar sensor assembly, the forward recognition camera stores DTC U023587.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U023587 |
Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message |
When the ignition switch is ON for 3 seconds or more, a communication data malfunction between the forward recognition camera and the millimeter wave radar sensor assembly continues for approximately 2 seconds or more. |
|
|
Pattern |
DTC output part name (Display on Techstream) |
Suspected Area (Malfunction Status) |
|||
|---|---|---|---|---|---|
|
Forward Recognition Camera |
Millimeter Wave Radar Sensor Assembly |
||||
|
Lane Control |
Forward Recognition Camera (Front Lighting Control) |
Pre-Collision System |
Radar Cruise2 |
||
|
U023587 |
U023587 |
U023A87 |
U023A87 |
||
|
○: DTC is output
-: DTC is not output |
|||||
|
Pattern1 |
○ |
○ |
○ |
○ |
Harness or connector (Open or short) |
|
Forward recognition camera (Internal malfunction) |
|||||
|
Millimeter wave radar sensor assembly (Internal malfunction) |
|||||
|
Pattern2 |
○ |
○ |
- |
- |
Forward recognition camera (Internal malfunction) |
|
Millimeter wave radar sensor assembly (Internal malfunction) |
|||||
HINT:
If the DTCs are output simultaneously, the inspection area can be narrowed down.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
-
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
![2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ]; CRUISE CONTROL: FRONT CAMERA: TARGET ADJUSTMENT(ONE TIME RECOGNITION)](/t3Portal/stylegraphics/info.gif)
Sequential Recognition: Click here
Driving Adjustment: Click here
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
-
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
HINT:
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click here
Flat Surface Target: Click here
Driving Adjustment: Click here
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
-
When disconnecting and reconnecting the auxiliary battery.
Click here
HINT:
If there are communication malfunctions for systems other than the forward recognition camera and millimeter wave radar sensor assembly, refer to "HOW TO PROCEED WITH TROUBLESHOOTING" for the CAN Communication System.
for Gasoline Model: Click here
for HV Model: Click here
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Read each DTC and check the diagnosis pattern using the table below.
Chassis > Lane Control > Trouble Codes
Body Electrical > Front Recognition Camera (Front Lighting Control) > Trouble Codes
Body Electrical > Pre-Collision System > Trouble Codes
Powertrain > Radar Cruise2 > Trouble Codes
|
Pattern |
DTC output part name (Display on Techstream / Output DTC) |
|||
|---|---|---|---|---|
|
Lane Control |
Forward Recognition Camera (Front Lighting Control) |
Pre-Collision System |
Radar Cruise2 |
|
|
Pattern 1 |
U023587 |
U023587 |
U023A87 |
U023A87 |
|
Pattern 2 |
U023587 |
U023587 |
- |
- |
|
Result |
Proceed to |
|---|---|
|
Pattern 1 |
A |
|
Pattern 2 |
B |
| B |
|
|
|
2. |
CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the P8 forward recognition camera connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
P8-6 (CANH) - P8-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
P8-6 (CANH) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
P8-12 (CANL) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
P8-6 (CANH) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
P8-12 (CANL) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| OK |
|
|
|
3. |
CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the B9 millimeter wave radar sensor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
B9-5 (CA1P) - B9-6 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
|
B9-5 (CA1P) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
B9-6 (CA1N) - Body ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
|
B9-5 (CA1P) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
|
B9-6 (CA1N) - +B |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR |
|
4. |
CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
(a) Disconnect the P8 forward recognition camera connector.
(b) Using an oscilloscope, check the waveform.
Measurement Condition:
|
Tester Connection |
Condition |
Tool Setting |
Specified Condition |
|---|---|---|---|
|
P8-6 (CANH) - P8-12 (CANL) |
Ignition switch ON |
1 V/DIV., 100 μs./DIV. |
Waveform generation |
| OK |
|
| NG |
|
|
|