Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM10000000219LF
Model Year Start: 2022 Model: RAV4 HV Prod Date Range: [12/2021 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P300449; High Voltage Power Resource Circuit Short during Pre-Charge; 2022 - 2024 MY RAV4 HV [12/2021 -        ]

DTC

P300449

High Voltage Power Resource Circuit Short during Pre-Charge

DTC SUMMARY

MALFUNCTION DESCRIPTION

The hybrid vehicle control ECU assembly monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects an open circuit malfunction.

The cause of this malfunction may be one of the following:

Inverter voltage sensor (VH) internal circuit malfunction

  • Voltage sensor (VH) malfunction
  • Motor generator control ECU (MG ECU) malfunction
  • Communication (wire harness) malfunction

High voltage system malfunction

  • HV battery malfunction
  • HV battery junction block assembly malfunction
  • Inverter with converter assembly malfunction
  • High-voltage wire harness malfunction
  • High-voltage connector or connection malfunction

Low-voltage circuit (12 V) malfunction

  • Hybrid vehicle control ECU assembly malfunction
  • HV battery junction block assembly malfunction
  • Low voltage wire harness malfunction
  • Low voltage connector malfunction

INSPECTION DESCRIPTION

System Diagram Range

Inspection Content

Reason

Inspection Step

*a

Check connection condition and wire harness continuity between hybrid vehicle control ECU assembly and HV battery junction block assembly

Check whether connectors are connected properly and check for an open circuit in the SMRP and SMRB primary lines

3 to 7

*b

Check system main relay

Check whether SMRB and SMRP stuck OFF

8, 9

*c

Check connection condition and high-voltage cable continuity between HV battery junction block assembly and inverter with converter assembly

Check for open circuit and defective connection (arc marks) due to looseness

10 to 12

*d

Check high-voltage cable and connection condition between HV battery and HV battery junction block assembly

Check for open circuit and defective connection (arc marks) due to looseness

13 to 17

*e

Check HV battery

Check whether HV battery voltage has drastically dropped below normal range

18, 19

DESCRIPTION

Refer to the description for DTC P0AE411.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AE411; Hybrid/EV Battery Precharge Contactor Circuit Short to Ground+

The hybrid vehicle control ECU assembly monitors the high-voltage wiring between the HV battery and the inverter with converter assembly and detects the following malfunction.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P300449

High Voltage Power Resource Circuit Short during Pre-Charge

Although a system main relay operation signal was sent when the ignition switch was operated, the system voltage is not sufficiently increased after boosting and the HV battery current does not flow.

High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.

The EV electric battery fuse is blown, the service plug grip is removed, the system main resistor is blown, SMRP or SMRB remains open, or the high-voltage cable has an open circuit.

(2 trip detection logic)

  • HV battery junction block assembly
  • HV floor under wire
  • Inverter with converter assembly
  • No. 1 HV supply stack sub-assembly
  • No. 2 HV supply stack sub-assembly
  • Hybrid battery terminal block
  • Electric vehicle battery plug assembly
  • Wire harness or connector

Does not come on

Master Warning:

Comes on

Related Data List

DTC No.

Data List

P300449

  • Hybrid/EV Battery Voltage
  • Hybrid/EV Battery Current
  • VL-Voltage before Boosting
  • VH-Voltage after Boosting

The following items can be helpful when performing repairs:

Data List

  • Ready Signal
  • Inter Lock Switch
  • SMRP Status
  • SMRB Status
  • SMRG Status

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Turn the ignition switch to ON (READY) and wait for 3 minutes or more.

    HINT:

    According to the display on the Techstream, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.

  7. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click here 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AA649,P1C7C49-P1C7F49,P1C8049; Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure+

Refer to the wiring diagram for the HV battery high-voltage line circuit.

Click here 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): HV Battery High-voltage Line Circuit+

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): PRECAUTION

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

    *a

    Without waiting for 10 minutes

  • Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

    If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

  • When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

    *a

    Dealer

    *b

    Battery Collection Agent

  • Before returning the HV battery, make sure to perform a recovery inspection.

    Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): RECOVERY INSPECTION

  • Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

    Click here 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): RECOVERY INSPECTION

  • Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.
  • After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control, Motor Generator, HV Battery / Trouble Codes.

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Powertrain > Motor Generator > Trouble Codes

Powertrain > HV Battery > Trouble Codes

Result

Proceed to

P300449 only is output, or DTCs except the ones in the table below are also output.

A

DTCs of hybrid control system in the tables below are output.

B

DTCs of motor generator control system in the tables below are output.

C

DTCs of hybrid battery system in the tables below are output.

D

Malfunction Content

System

Relevant DTC

Microcomputer malfunction

Hybrid control system

P0A1B49

Drive Motor "A" Control Module Internal Electronic Failure

P060647

Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure

P060687

Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message

P060A47

Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure

P060A87

Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message

P1C9E9F

Hybrid/EV System Reset Stuck Off

P060B49

Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure

Motor generator control system

P0A1B1F

Generator Control Module Circuit Intermittent

P0A1A47

Generator Control Module Watchdog / Safety μC Failure

P0A1A49

Generator Control Module Internal Electronic Failure

P1C2A1C

Generator A/D Converter Circuit Circuit Voltage Out of Range

P1C2A49

Generator A/D Converter Circuit Internal Electronic Failure

P313383

Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect

P313386

Communication Error from Generator to Drive Motor "A" Signal Invalid

P313387

Communication Error from Generator to Drive Motor "A" Missing Message

Hybrid battery system

P060B49

Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure

P060687

Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message

P060A47

Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure

P060A87

Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message

P060B16

Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold

P0E2D00

Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance

Power source circuit malfunction

Motor generator control system

P06D61C

Generator Control Module Offset Power Circuit Voltage Out of Range

Communication system malfunction

Hybrid control system

P312387

Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message

U011187

Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message

Sensor and actuator circuit malfunction

Hybrid control system

P0AD915

Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open

P0AD911

Hybrid/EV Battery Positive Contactor Circuit Short to Ground

P0AE415

Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open

P0AE411

Hybrid/EV Battery Precharge Contactor Circuit Short to Ground

P0ADD15

Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open

P0ADD11

Hybrid/EV Battery Negative Contactor Circuit Short to Ground

P0B231C

Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range

P0ABF00

Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance

Hybrid battery system

P0ABF11

Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground

P0B0E11

Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground

P0B0E15

Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open

P0ABF15

Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open

P301A1C

Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range

P1A001C

Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range

P1AFD1C

Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range

P0ABF28

Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure

P0ABF2A

Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range

P1CBB12

Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery

P1CBB14

Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open

P0B1362

Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure

System malfunction

Hybrid control system

P0C7600

Hybrid/EV Battery System Discharge Time Too Long

P0D2D1C

Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range

P1C8149

High Voltage Power Resource Circuit Consumption Circuit Short

P1C8249

High Voltage Power Resource Circuit Over Loading

P1C8349

High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction

P0A1F94

Hybrid/EV Battery Energy Control Module Unexpected Operation

Motor generator control system

P0D2D16

Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold

P0D2D17

Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold

P1CB69E

Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On

P0CA300

DC/DC Converter Step Up Voltage Performance

HINT:

  • P300449 may be output as a result of the malfunction indicated by the DTCs above.
    1. The chart above is listed in inspection order of priority.
    2. Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)

(e) Turn the ignition switch off.

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM)

D

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

A

2.

CHECK FREEZE FRAME DATA (HYBRID CONTROL)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

(d) Read the freeze frame data of DTC P300449.

Powertrain > Hybrid Control > Trouble Codes

Standard:

Freeze Frame Data Itm

Specified Condition

VH-Voltage after Boosting

Below 50 V [*1]

Hybrid/EV Battery Voltage - VL-Voltage before Boosting

-40 to 40 V [*2]

Result

Cause

Proceed to

Specified condition [*1] and [*2] are met

Inverter

A

Except above

Other

B

(e) Turn the ignition switch off.

A

REPLACE INVERTER WITH CONVERTER ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL

B

3.

CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU ASSEMBLY CONNECTOR)

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P056014; System Voltage (BATT) Circuit Short to Ground or Open+

NG

CONNECT SECURELY

OK

4.

CHECK CONNECTOR CONNECTION CONDITION (FLOOR WIRE CONNECTOR)

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AA000; Hybrid/EV Battery Positive Contactor Circuit Stuck Closed+

Result

Proceed to

OK

A

NG (The connector is not connected securely.)

B

NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.)

C

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

5.

CHECK CONNECTOR CONNECTION CONDITION (HV BATTERY JUNCTION BLOCK ASSEMBLY CONNECTOR)

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AA000; Hybrid/EV Battery Positive Contactor Circuit Stuck Closed+

NG

CONNECT SECURELY

OK

6.

CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the M32 HV battery junction block assembly connector.

(d) Disconnect the A31 hybrid vehicle control ECU assembly connector.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A31-16 (SMRB) - M32-1 (SMRB)

Ignition switch off

Below 1 Ω

A31-15 (SMRP) - M32-2 (SMRP)

Ignition switch off

Below 1 Ω

*a

Front view of wire harness connector

(to Hybrid Vehicle Control ECU Assembly)

*b

Front view of wire harness connector

(to HV Battery Junction Block Assembly)

(f) Reconnect the A31 hybrid vehicle control ECU assembly connector.

(g) Reconnect the M32 HV battery junction block assembly connector.

(h) Install the No. 1 HV battery cover panel RH.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.

CHECK HARNESS AND CONNECTOR (HV BATTERY JUNCTION BLOCK ASSEMBLY - BODY GROUND)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the M32 HV battery junction block assembly connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M32-3 (GND) - Body ground

Ignition switch off

Below 1 Ω

*a

Front view of wire harness connector

(to HV Battery Junction Block Assembly)

(e) Reconnect the M32 HV battery junction block assembly connector.

(f) Install the No. 1 HV battery cover panel RH.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRB)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the HV battery junction block assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without harness connected

(HV Battery Junction Block Assembly)

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

z32-1 (+) - Y3-1 (CBI)

Auxiliary battery voltage applied between terminals M32-1 (SMRB) and M32-3 (GND)

Below 1 Ω

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M32-1 (SMRB) - M32-3 (GND)

-40 to 80°C (-40 to 176°F)

25.0 to 59.0 Ω

(e) Install the HV battery junction block assembly.

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

OK

9.

INSPECT HV BATTERY JUNCTION BLOCK ASSEMBLY (SMRP)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the HV battery junction block assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without harness connected

(HV Battery Junction Block Assembly)

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

z21-1 (-) - Y4-1 (CEI)

Auxiliary battery voltage applied between terminals M32-2 (SMRP) and M32-3 (GND)

24.3 to 29.7 Ω

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M32-2 (SMRP) - M32-3 (GND)

-40 to 80°C (-40 to 176°F)

140 to 290 Ω

(e) Install the HV battery junction block assembly.

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

OK

10.

CHECK INVERTER WITH CONVERTER ASSEMBLY (HV FLOOR UNDER WIRE)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Check that the bolts for the HV floor under wire are tightened to the specified torque, the HV floor under wire is connected securely, and there are no contact problems.

Specified Condition:

T = 8.0 N*m (82 kgf*cm, 71 in.*lbf)

(c) Disconnect the HV floor under wire from the inverter with converter assembly.

(d) Check for arc marks on the terminals for the HV floor under wire and inverter with converter assembly.

Result

Proceed to

The terminals are connected securely and there are no contact problems.

There are no arc marks.

A

The terminals are not connected securely and there is a contact problem.

There are arc marks.

B

The terminals are not connected securely and there is a contact problem.

There are no arc marks.

C

The terminals are connected securely and there are no contact problems.

There are arc marks.

B

(e) Reconnect the HV floor under wire.

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

A

11.

CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV FLOOR UNDER WIRE)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Check that the HV floor under wire is connected securely, and there are no contact problems.

(d) Disconnect the HV floor under wire connectors from the HV battery junction block assembly.

(e) Check for arc marks on the terminals of the HV floor wire and the HV battery junction block assembly.

Result

Proceed to

The terminals are connected securely and there are no contact problems.

There are no arc marks.

A

The terminals are not connected securely and there is a contact problem.

There are arc marks.

B

The terminals are not connected securely and there is a contact problem.

There are no arc marks.

C

The terminals are connected securely and there are no contact problems.

There are arc marks.

B

(f) Reconnect the HV floor under wire.

(g) Install the No. 1 HV battery cover panel RH.

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

A

12.

CHECK FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the HV floor under wire connectors from the HV battery junction block assembly.

(d) Disconnect the HV floor under wire connector from the inverter with converter assembly.

(e) Measure the resistance according to the value(s) in the table below.

*a

HV Floor Under Wire

(Inverter with Converter Assembly Side)

*b

HV Floor Under Wire

(HV Battery Junction Block Assembly Side)

Standard Resistance:

Tester Connection

Condition

Specified Condition

Y8-1 (CBI) - Y3-1 (CBI)

Ignition switch off

Below 1 Ω

Y8-2 (CEI) - Y4-1 (CEI)

Ignition switch off

Below 1 Ω

NOTICE:

Be sure not to damage or deform the terminal being inspected.

(f) Reconnect the HV floor under wire connector to the inverter with converter assembly.

(g) Reconnect the HV floor under wire connectors to the HV battery junction block assembly.

(h) Install the No. 1 HV battery cover panel RH.

NG

REPLACE FLOOR UNDER WIRE 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL

OK

13.

CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Check the 2 HV battery high voltage connectors are connected securely, and there are no contact problems.

(d) Disconnect the 2 HV battery high voltage connectors from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(e) Check for arc marks on the terminals of the HV battery high voltage connectors and HV battery junction block assembly.

Result

Proceed to

The terminals are connected securely and there are no contact problems.

There are no arc marks.

A

The terminals are not connected securely and there is a contact problem.

There are arc marks.

B

The terminals are not connected securely and there is a contact problem.

There are no arc marks.

C

The terminals are connected securely and there are no contact problems.

There are arc marks.

B

(f) Reconnect the 2 HV battery high voltage connectors.

(g) Install the No. 1 HV battery cover panel RH.

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

A

14.

CHECK HYBRID BATTERY TERMINAL BLOCK (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Check the HV battery high voltage connector and electric vehicle battery plug connector securely, and there are no contact problems.

(d) Disconnect the HV battery high voltage connector and electric vehicle battery plug connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(e) Check for arc marks on the terminals of the HV battery high voltage connectors and hybrid battery terminal block.

Result

Proceed to

The terminals are connected securely and there are no contact problems.

There are no arc marks.

A

The terminals are not connected securely and there is a contact problem.

There are arc marks.

B

The terminals are not connected securely and there is a contact problem.

There are no arc marks.

C

The terminals are connected securely and there are no contact problems.

There are arc marks.

B

(f) Reconnect the HV battery high voltage connector and electric vehicle battery plug connector.

(g) Install the No. 1 HV battery cover panel RH.

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

A

15.

CHECK HV SUPPLY STACK SUB-ASSEMBLY (HV BATTERY HIGH VOLTAGE CONNECTOR CONNECTION CONDITION)

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the upper HV battery cover sub-assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+

(c) Check that the HV battery high voltage connector is connected securely, and there are no contact problems.

(d) Disconnect the HV battery high voltage connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(e) Check for arc marks on the terminals of the HV battery high voltage connector.

Result

Proceed to

The terminals are connected securely and there are no contact problems.

There are no arc marks.

A

The terminals are not connected securely and there is a contact problem.

There are arc marks.

B

The terminals are not connected securely and there is a contact problem.

There are no arc marks.

C

The terminals are connected securely and there are no contact problems.

There are arc marks.

B

(f) Connect the HV battery high voltage connector.

(g) Install the upper HV battery cover sub-assembly.

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

A

16.

CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the 2 electric vehicle battery plug assembly connectors.

(d) Measure the resistance according to the value(s) in the table below.

*a

Electric Vehicle Battery Plug Assembly Connector

(HV Battery Junction Block Assembly Side)

*b

Electric Vehicle Battery Plug Assembly Connector

(Hybrid Battery Terminal Block Side)

*c

Service Plug Grip Removed

(Service Plug Grip Connecting Terminals)

-

-

Standard Resistance:

Tester Connection

Condition

Specified Condition

z32-1 (+) - Service plug grip connecting terminal 1

Ignition switch off

Below 1 Ω

z31-1 - Service plug grip connecting terminal 2

Ignition switch off

Below 1 Ω

(e) Reconnect the 2 electric vehicle battery plug assembly connectors.

(f) Install the No. 1 HV battery cover panel RH.

NG

REPLACE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: SERVICE PLUG GRIP: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: SERVICE PLUG GRIP: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: SERVICE PLUG GRIP: REMOVAL

OK

17.

CHECK HYBRID BATTERY TERMINAL BLOCK

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the HV battery high voltage connector and electric vehicle battery plug assembly connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

z31-1 - z30-1

Ignition switch off

Below 1 Ω

*a

Component without harness connected

(Hybrid Battery Terminal Block)

(e) Reconnect the HV battery high voltage connector and electric vehicle battery plug assembly connector to the hybrid battery terminal block.

(f) Install the No. 1 HV battery cover panel RH.

NG

REPLACE HYBRID BATTERY TERMINAL BLOCK 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: FUSE BOX (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: FUSE BOX (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: FUSE BOX (for LITHIUM-ION BATTERY): REMOVAL

OK

18.

CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the upper HV battery cover sub-assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the HV battery high voltage connector from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(d) Disconnect the HV battery high voltage connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

z30-1 - A-1

Ignition switch off

50 V or higher

CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.

*a

No. 2 HV Supply Stack Sub-assembly Connector

(Hybrid Battery Terminal Block Side)

*b

No. 2 HV Supply Stack Sub-assembly Connector

(No. 1 HV Supply Stack Sub-assembly Side)

(f) Reconnect the 2 HV battery high voltage connectors.

(g) Install the upper HV battery cover sub-assembly.

NG

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL

OK

19.

CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the upper HV battery cover sub-assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: BATTERY ECU (for LITHIUM-ION BATTERY): REMOVAL+

(c) Remove the electric vehicle battery plug assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: BATTERY PLUG (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: BATTERY PLUG (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: BATTERY PLUG (for LITHIUM-ION BATTERY): REMOVAL+

(d) Disconnect the HV battery high voltage connector from the HV battery junction block assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(e) Disconnect the HV battery high voltage connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.

(f) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

z21-1(-) - A-1

Ignition switch off

50 V or higher

CAUTION:

Do not allow the probes of the electrical tester to contact each other during this inspection.

*a

No. 1 HV Supply Stack Sub-assembly Connector

(HV Battery Junction Block Assembly Side)

*b

No. 1 HV Supply Stack Sub-assembly Connector

(No. 2 HV Supply Stack Sub-assembly Side)

(g) Reconnect the 2 HV battery high voltage connectors.

(h) Install the electric vehicle battery plug assembly.

(i) Install the upper HV battery cover sub-assembly.

NG

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY STACK (for LITHIUM-ION BATTERY): REMOVAL

OK

20.

CHECK FOR INTERMITTENT PROBLEMS

(a) Check for intermittent problems.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): CHECK FOR INTERMITTENT PROBLEMS

Result

Proceed to

Problem symptom does not recur.

A

Problem symptom recurs.

B

HINT:

  • Since 2 trip detection logic is used, the DTC detection condition must be met twice.
  • If DTC P300449 is output again after performing the inspection, replace the inverter with converter assembly. If DTC P300449 is not output again, replace the HV battery junction block assembly.
B

REPLACE INVERTER WITH CONVERTER ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL

A

21.

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL

NEXT

22.

CHECK HYBRID VEHICLE CONTROL ECU ASSEMBLY (CHECK FOR NORMAL OPERATION)

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P1C8449; High Voltage Power Resource Circuit Short during Ready ON+

Result

Proceed to

Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V.

A

Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more.

B

A

END

B

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HYBRID VEHICLE CONTROL ECU: REMOVAL