Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM10000000219LE
Model Year Start: 2022 Model: RAV4 HV Prod Date Range: [12/2021 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P1C8149,P1C8249; High Voltage Power Resource Circuit Consumption Circuit Short; 2022 - 2024 MY RAV4 HV [12/2021 -        ]

DTC

P1C8149

High Voltage Power Resource Circuit Consumption Circuit Short

DTC

P1C8249

High Voltage Power Resource Circuit Over Loading

DTC SUMMARY

MALFUNCTION DESCRIPTION

The hybrid vehicle control ECU assembly monitors the high-voltage wiring between the HV battery and inverter with converter assembly and detects a short circuit malfunction or high-voltage system operation malfunction.

The cause of this malfunction may be one of the following:

Battery current sensor (IB) circuit malfunction

  • Battery current sensor (IB) malfunction
  • Motor generator control ECU (MG ECU) malfunction
  • Communication (wire harness) malfunction

High voltage system malfunction

  • HV battery malfunction
  • HV battery junction block assembly malfunction
  • Inverter with converter assembly malfunction
  • Air conditioner system malfunction
  • High-voltage wire harness malfunction
  • High-voltage connector or connection malfunction

Low-voltage circuit (12 V) malfunction

  • Hybrid vehicle control ECU assembly malfunction
  • Low voltage wire harness malfunction
  • Low voltage connector malfunction

INSPECTION DESCRIPTION

System Diagram Location

Inspection Content

Reason

Inspection Step

*a

Check high-voltage wiring connection condition of the air conditioner compressor with motor assembly

Check for short circuit

2, 4

*b

Check the high voltage cables between the HV battery junction block assembly and inverter with converter assembly.

Check for short circuit

3, 5

DESCRIPTION

Refer to the description for DTC P0AE411.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AE411; Hybrid/EV Battery Precharge Contactor Circuit Short to Ground+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

P1C8149

High Voltage Power Resource Circuit Consumption Circuit Short

High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.

Excessive overcurrent equal to a short occurs during precharge (time from when SMRP turns on until SMRG turns on).

(1 trip detection logic)

  • Air conditioning wire
  • Compressor with motor assembly
  • Inverter with converter assembly
  • HV battery junction block assembly
  • HV floor under wire

Does not come on

Master Warning:

Comes on

P1C8249

High Voltage Power Resource Circuit Over Loading

High-voltage circuit malfunctions between the HV battery and inverter with converter assembly.

Small battery overcurrent occurs during precharge (time from when SMRP turns on until SMRG turns on) and current continues to flow after precharge.

(1 trip detection logic)

  • Air conditioning wire
  • Compressor with motor assembly
  • Inverter with converter assembly
  • HV battery junction block assembly
  • HV floor under wire

Does not come on

Master Warning:

Comes on

Related Data List

DTC No.

Data List

P1C8149

  • Hybrid/EV Battery Voltage
  • Hybrid/EV Battery Current
  • VL-Voltage before Boosting
  • VH-Voltage after Boosting

P1C8249

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): UTILITY

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON (READY) and wait for 30 seconds or more.
  6. Turn the ignition switch off and wait for 2 minutes or more.
  7. Turn the ignition switch to ON and turn the Techstream on.
  8. Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
  9. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform driving pattern again.

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click here 2022 - 2024 MY RAV4 HV [12/2021 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): P0AA649,P1C7C49-P1C7F49,P1C8049; Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure+

CAUTION / NOTICE / HINT

CAUTION:

  • Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
    • Inspecting the high-voltage system
    • Disconnecting the low voltage connector of the inverter with converter assembly
    • Disconnecting the low voltage connector of the HV battery
  • To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
  • After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here 2020 - 2024 MY RAV4 HV [06/2020 -        ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): PRECAUTION

    HINT:

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

    *a

    Without waiting for 10 minutes

  • If this DTC is output, do not turn the ignition switch to ON (READY) until the repair has been completed. This DTC means an excessive amperage flow through the system main resistor. The system main resistor may overheat and be damaged if the ignition switch is turned to ON (READY) repeatedly before repair.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here 2019 - 2024 MY RAV4 RAV4 HV [11/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR, HV BATTERY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Enter the following menus: Powertrain / Hybrid Control, Motor Generator, HV Battery / Trouble Codes.

(d) Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes

Powertrain > Motor Generator > Trouble Codes

Powertrain > HV Battery > Trouble Codes

Result

Proceed to

P1C8149 or P1C8249 only is output, or DTCs except the ones in the tables below are also output.

A

DTCs of hybrid control system in the tables below are output.

B

DTCs of motor generator control system in the tables below are output.

C

DTCs of hybrid battery system in the tables below are output.

D

Malfunction Content

System

Relevant DTC

Microcomputer malfunction

Hybrid control system

P060647

Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure

P060B49

Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure

P060687

Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message

P060A47

Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure

P060A87

Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message

Hybrid battery system

P060B49

Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure

P060687

Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message

P060A47

Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure

P060A87

Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message

P060B16

Hybrid/EV Battery Energy Control Module A/D Processing Circuit Voltage Below Threshold

P0E2D00

Hybrid/EV Battery Energy Control Module Hybrid/EV Battery Monitor Performance

Communication system malfunction

Hybrid control system

U011187

Lost Communication with Hybrid/EV Battery Energy Control Module "A" Missing Message

Sensor and actuator circuit malfunction

Hybrid control system

P0B231C

Hybrid/EV Battery "A" Voltage Sensor Voltage Out of Range

P0ABF00

Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance

Motor generator control system

P0A1114

DC/DC Converter Enable Circuit Short to Ground or Open

P0A1112

DC/DC Converter Enable Circuit Short to Battery

P1CCC96

DC/DC Converter Enable Component Internal Failure

Hybrid battery system

P0ABF11

Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground

P0B0E11

Hybrid/EV Battery Current Sensor "B" Circuit Short to Ground

P0B0E15

Hybrid/EV Battery Current Sensor "B" Circuit Short to Auxiliary Battery or Open

P0ABF15

Hybrid/EV Battery Current Sensor "A" Circuit Short to Auxiliary Battery or Open

P301A1C

Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range

P1A001C

Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range

P1AFD1C

Flying Capacitor/Internal Control Module Hybrid/EV Battery Monitor Voltage Out of Range

P0ABF28

Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure

P0ABF2A

Hybrid/EV Battery Current Sensor "A" Signal Stuck In Range

P1CBB12

Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Auxiliary Battery

P1CBB14

Hybrid/EV Battery Current Sensor Power Supply Circuit Short to Ground or Open

P0B1362

Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure

System malfunction

Hybrid control system

P0A1F94

Hybrid/EV Battery Energy Control Module Unexpected Operation

Motor generator control system

P0D3319

DC/DC Converter Circuit Current Above Threshold

HINT:

  • P1C8149 or P1C8249 may be output as a result of the malfunction indicated by the DTCs above.
    1. The chart above is listed in inspection order of priority.
    2. Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)

(e) Turn the ignition switch off.

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

C

GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM)

D

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

A

2.

CHECK COMPRESSOR WITH MOTOR ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the HV air conditioning wire connector from the inverter with converter assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

(Tester Probe Polarity)

Condition

Specified Condition

Z2-2 (ACPE) (Negative (-) probe) - Z2-1 (ACPB) (Positive (+) probe)

Ignition switch off

100 kΩ or higher

NOTICE:

  • Do not use a megohmmeter.
  • Read the resistance after the value has stabilized.
  • Be sure to inspect with connecting the tester probes to the tips of the terminal.

*a

HV Air Conditioning Wire

(Inverter with Converter Assembly Side)

*b

Tip of Terminal

(d) Reconnect the HV air conditioning wire connector.

NG

GO TO STEP 4

OK

3.

CHECK FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the HV floor under wire connector from the inverter with converter assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Y8-1 (CBI) - Y8-2 (CEI)

Ignition switch off

10 kΩ or higher

NOTICE:

Be sure not to damage or deform the terminal being inspected.

*a

HV Floor Under Wire

(Inverter with Converter Assembly Side)

(d) Reconnect the HV floor under wire connector.

OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER (for AWD): REMOVAL

NG

GO TO STEP 5

4.

CHECK HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Disconnect the HV air conditioning wire connector from the inverter with converter assembly.

(c) Disconnect the HV air conditioning wire from the compressor with motor assembly.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Z2-2 (ACPE) - Z2-1 (ACPB)

Ignition switch off

10 kΩ or higher

NOTICE:

Be sure to inspect with connecting the tester probes to the tips of the terminal.

*a

HV Air Conditioning Wire

(Inverter with Converter Assembly Side)

*b

Tip of Terminal

(e) Reconnect the HV air conditioning wire connector to the inverter with converter assembly.

(f) Reconnect the HV air conditioning wire to the compressor with motor assembly.

OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HEATING / AIR CONDITIONING: COMPRESSOR (for A25A-FXS): REMOVAL

NG

REPLACE HV AIR CONDITIONING WIRE

5.

CHECK FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.

(b) Remove the No. 1 HV battery cover panel RH.

Click here 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+ 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV BATTERY (for LITHIUM-ION BATTERY): REMOVAL+

(c) Disconnect the HV floor under wire connectors from the HV battery junction block assembly.

(d) Disconnect the HV floor under wire connector from the inverter with converter assembly.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Y8-1 (CBI) - Y8-2 (CEI)

Ignition switch off

10 kΩ or higher

NOTICE:

Be sure not to damage or deform the terminal being inspected.

*a

HV Floor Under Wire

(Inverter with Converter Assembly Side)

(f) Reconnect the HV floor under wire connector to the inverter with converter assembly.

(g) Reconnect the HV floor under wire connectors to the HV battery junction block assembly.

(h) Install the No. 1 HV battery cover panel RH.

OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

NG

REPLACE FLOOR UNDER WIRE 2022 MY RAV4 HV [12/2021 - 10/2022]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL 2023 MY RAV4 HV [10/2022 - 10/2023]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL 2024 MY RAV4 HV [10/2023 -        ]; HYBRID / BATTERY CONTROL: FRAME WIRE: REMOVAL