| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000215N4 |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: LIGHTING (EXT): LIGHTING SYSTEM: Daytime Running Light Circuit; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ] | ||
|
Daytime Running Light Circuit |
DESCRIPTION
The main body ECU (multiplex network body ECU) controls the daytime running lights.
WIRING DIAGRAM
for Triple Beam Headlight
for Single Beam Headlight (w/o Accessory Light)
for Single Beam Headlight (w/ Accessory Light)
CAUTION / NOTICE / HINT
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
-
w/ Smart Key System:
Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
PROCEDURE
|
1. |
CHECK VEHICLE TYPE |
(a) Check the vehicle type.
|
Result |
Proceed to |
|---|---|
|
for Triple Beam Headlight |
A |
|
for Single Beam Headlight (w/o Accessory Light) |
B |
|
for Single Beam Headlight (w/ Accessory Light) |
C |
| B |
|
| C |
|
|
|
2. |
CHECK OPERATION (LOW BEAM HEADLIGHTS) |
(a) Check the operation of the low beam headlights.
OK:
The low beam headlights operate normally.
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Daytime Running Light |
Daytime running lights |
OFF or ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Daytime Running Light |
OK:
Daytime running lights illuminate.
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
4. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Disconnect the A62 headlight assembly LH connector.
(b) Disconnect the A61 headlight assembly RH connector.
(c) Disconnect the 4F instrument panel junction block assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A62-3 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A61-3 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A62-3 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
|
A61-3 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Remove the instrument panel junction block assembly.
Click here
![2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL](/t3Portal/stylegraphics/info.gif)
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4F-28 - A-25 (DRL) |
Always |
Below 1 Ω |
| OK |
|
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
|
| NG |
|
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
|
6. |
CHECK OPERATION (LOW BEAM HEADLIGHTS) |
(a) Check the operation of the low beam headlights.
OK:
The low beam headlights operate normally.
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
7. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Daytime Running Light |
Daytime running lights |
OFF or ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Daytime Running Light |
OK:
Daytime running lights illuminate.
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
8. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
- *1: Turn Light for LED Type
- *2: Turn Light for Bulb Type
(a) Disconnect the A98*1 or A99*2 headlight assembly LH connector.
(b) Disconnect the A96*1 or A97*2 headlight assembly RH connector.
(c) Disconnect the 4F instrument panel junction block assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Headlight for LED Type
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A98-7 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A96-7 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A98-7 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
|
A96-7 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
Headlight for Bulb Type
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A99-3 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A97-3 (B) - 4F-28 |
Always |
Below 1 Ω |
|
A99-3 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
|
A97-3 (B) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
9. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Daytime Running Light |
Daytime running lights |
OFF or ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Daytime Running Light |
OK:
Daytime running lights or accessory lights* illuminate.
*: w/ Accessory Light
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
|
|
10. |
CHECK HARNESS AND CONNECTOR (DRL RELAY - BATTERY) |
(a) Remove the DRL relay.
|
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
INSPECT DRL RELAY |
(a) Remove the DRL relay.
(b) Inspect the DRL relay.
Click here
| NG |
|
REPLACE DRL RELAY |
|
|
12. |
CHECK HARNESS AND CONNECTOR (DRL RELAY - HEADLIGHT ASSEMBLY) |
(a) Remove the DRL relay.
(b) Disconnect the A98 headlight assembly LH connector.
(c) Disconnect the A96 headlight assembly RH connector.
(d) Disconnect the B16 daytime running light assembly LH connector.
(e) Disconnect the B15 daytime running light assembly RH connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (DRL relay) - A98-7 (B) |
Always |
Below 1 Ω |
|
3 (DRL relay) or A96-7 (B) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
13. |
CHECK HARNESS AND CONNECTOR (DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Remove the DRL relay.
(b) Disconnect the 4F instrument panel junction block assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (DRL relay) - 4F-28 |
Always |
Below 1 Ω |
|
2 (DRL relay) or 4F-28 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
14. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Remove the instrument panel junction block assembly.
Click here
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
4F-28 - A-25 (DRL) |
Always |
Below 1 Ω |
| OK |
|
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
|
| NG |
|
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
|
|
|